A. anycast address
B. site-local multicast
C. global address of the link
D. unique local address
E. link-local address
您可能感兴趣的试卷
你可能感兴趣的试题
A.On-Passive
B.On-Auto
C.Passive-Active
D.Desirable-Auto
E.Active-Active
F.Desirable-Desirable
A. IPv6 prefixes
B. link-local addresses
C. solicited node multicast addresses
D. IPv6 prefixes and topology information
A. An IPv4-compatible tunnel is a static tunnel, but an 6to4 tunnel is a semiautomatic tunnel.
B. The deployment of a IPv4-compatible tunnel requires a special code on the edge routers, but a 6to4 tunnel does not require any special code.
C. An IPv4-compatible tunnel is typically used only between two IPv6 domains, but a 6to4 tunnel is used to connect to connect two or more IPv6 domains.
D. For an IPv4-compatible tunnel, the ISP assigns only IPv4 addresses for each domain, but for a 6to4 tunnel, the ISP assigns only IPv6 addresses for each domain.
A.configure a hard-to-guess VTP domain name
B.use a hard-to-guess VTP password
C.use VTP transparent mode
D.implement VTP version 3
A. prefixes received from any other BGP peer and prefixes locally originated via networkstatements or redistributed to BGP
B. all prefixes in its IP routing table
C. only prefixes received from EBGP peers and prefixes locally originated via network statements or redistributed
D. only prefixes received from EBGP peers and prefixes received from route reflectors
E. all prefixes in its routing table except the prefixes received from other EBGP peers
F. all prefixes in its routing table except the prefixes received from other IBGP peers
A.excessive collisions
B.FCS errors
C.runts
D.late collisions
A.interface gig3/1 spanning-tree guard root
B.interface gig3/1 spanning-tree root guard
C.interface gig3/1 spanning-tree root-guard
D.interface gig3/1 spanning-tree root-guard default
A. prefixes received from any other BGP peer and prefixes locally originated via network statements or redistributed
B. all prefixes in its routing table
C. prefixes received from EBGP peers and prefixes locally originated via network statements or redistributed
D. prefixes received from EBGP peers and prefixes received from route reflectors
E. prefixes received from other IBGP peers, prefixes received from EBGP peers, and prefixes redistributed to BGP
F. prefixes received from other IBGP peers and prefixes received from route reflectors
A.802.1s supports a reduced number of spanning-tree instances.
B.802.1s has better convergence times than 802.1w.
C.802.1s does not support load balancing over the same physical topology.
D.The CPU utilization for 802.1s is lower than the CPU utilization for 802.1w.
A.service timestamps log datetimec msec
B.logging timestamps msec
C.syslog timestamps hour minute second miliseconds
D.service logging timestamp msec
E.logging service timestamp msec
最新试题
Which of the following is true about the MPLS header and its EXP field size?()
Which two statements about SA caching are true?()
In Layer 2 topologies, spanning-tree failures can cause loops in the network. These unblocked loops cancause network failures because of excessive traffic. Which two Catalyst 6500 features can be used to limitexcessive traffic during spanning-tree loop conditions?()
What is the correct command to set the router ID for an OSPFv3 process?()
Two routers configured to run BGP have been connected to a firewall, one on the inside interface and one on the outside interface. BGP has been configured so the two routers should peer, including the correctBGP session endpoint addresses and the correct BGP session hop-count limit EBGP multihop. What is agood first test to see if BGP will work across the firewall?()
What is also called Type 0 authentication in OSPF on Cisco Routers?()
Which multicast address is reserved for cisco-rp-discovery?()
Choose two commands that are required to enable multicast on a router, when it is known that thereceivers use a specific functionality of IGMPv3.()
Which three options are valid ways to filter routes from a BGP peer?()
In GLBP,which router will answer on client ARP requests?()