单项选择题

Refer to the exhibit。A problem with network connectivity has been observed.It is suspected that the cable connected to switch port Fa0/9 on Switch 1 disconnected.What would be an effect of tis cable being disconnected?()

A.Host B would not be able to access the server in VLAN9 until the cable is reconnected
B.For less than a minute ,Host B would not be able to access the server in VLAN9.Then normal network function would resume.
C.Communication between VLAN3 and the other VLANs would be disabled
D.The transfer of files from Host B to the server in VLAN9 would be significantly slower.


您可能感兴趣的试卷

你可能感兴趣的试题

1.多项选择题

Refer to the exhibit. The network shown in the diagram is experiencing connectivity problems. Which of the following will correct the problems? ()

A.Configure the gateway on Host A as 10.1.1.1.
B.Configure the gateway on Host B as 10.1.2.254.
C.Configure the IP address of Host A as 10.1.2.2.
D.Configure the IP address of Host B as 10.1.2.2.
E.Configure the masks on both hosts to be 255.255.255.224.
F.Configure the masks on both hosts to be 255.255.255.240.

2.多项选择题

Refer to the graphic. R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem?()

A.All of the routers need to be configured for backbone Area 1.
B.R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.
C.A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.
D.The hello and dead interval timers are not set to the same values on R1 and R3.
E.EIGRP is also configured on these routers with a lower administrative distance.
F.R1 and R3 are configured in different areas.

4.单项选择题VLAN 3 is not yet configured on your switch.What happens if you set the switchport access vlan 3 commmand interface configuration mode?()

A.The command is accepted and the respective VLAN is added to vlan dat.
B.The command is rejected.
C.The command is accepted and you must configure the VLAN manually.
D.The port turns amber.

5.单项选择题In which circumstance are multiple copies of the same unicast frame likely to be transmitted in a switched LAN?()

A.after broken links are re-established
B.in an improperly implemented redundant topology
C.when upper-layer protocols require high reliability
D.during high traffic periods
E.when a dual ring topology is in use

6.多项选择题Which router IOS commands can be used to troubleshoot LAN connectivity problems?()

A.ping
B.tracert
C.ipconfig
D.show ip route
E.winipcfg
F.show interfaces

7.单项选择题

Refer to the exibit .An attempt to deny web access to a subnet blocks all traffic from the subnet.Which interface command immedicately removes the effect of ACL 102?()

A.no ip access-group 102 in
B.no ip access-group 102 out
C.no ip access-list 102 in
D.no ip access-class 102 out
E.no ip access-class 102 in

8.单项选择题What will happen if a private IP address is assigned to a public interface connected to an ISP?()

A.Addresses in a private range will be not routed on the Internet backbone.
B.Only the ISP router will have the capability to access the public network.
C.The NAT process will be used to translate this address in a valid IP address.
D.Several automated methods will be necessary on the private network.
E.A conflict of IP addresses happens, because other public routers can use the same range.

9.单项选择题

Refer to the exhibit. Give this output for SwitchC, what should the network administrator's next action be?()

A.Check the trunk encapsulation mode for SwitchC's fa0/1 port.
B.Check the duplex mode for SwitchC's fa0/1 port.
C.Check the duplex mode for SwitchA's fa0/2 port.
D.Check the trunk encapsulation mode for SwitchA's fa0/2 port.

10.单项选择题

Refer to the exhibit. A network technician is asked to design a small network with redundancy. The exhibit represents this design, with all hosts configured in the same VLAN. What conclusions can be made about this design?()

A.The design will function as intended
B.Spanning-tree will need to be used.
C.The router will not accept the addressing scheme.
D.The connection between switches should be a trunk.
E.The router interfaces must be encapsulated with the 802.1Q protocol.