A.BGP route-reflector should be in forwarding path of data coming from its clients
B.BGP route-reflector does not have to be in the forwarding path of data coming from its clients
C.BGP route-reflector will stop reflecting the routes if they’re not directly-connected clients
D.None of the above
您可能感兴趣的试卷
你可能感兴趣的试题
A.Failure detection
B.Failure reporting
C.IGP LSP/LSA originatio
D.Per-hop flooding time of new link state
E.Number of hops that need to be notified of new link state
A.MPLS LDP must be enabled.
B.BGP routing protocol must be running.
C.Named access-lists must be configured.
D.Symmetrical routing is required.
E.Domain name must be defined
A.Allows incoming TCP connections destined to port 179
B.Allows incoming TCP connections sourced from port 179
C.Allows incoming TCP connections from 1.1.1.1 and destined to,or sourced from port 179
D.Allows incoming TCP connections from 1.1.1.1 that are destined to port 179
E.Allows incoming TCP connections from 1.1.1.1 that are sourced from port 179
A.First (most significant ) octet is FF in hex
B.Starts with a prefix of FE80 to FEBF in hex
C.Starts with a prefix of FECO to FEFF in hex
D.Second octet contains a 4-bit multicast scope field
E.Last 64 bit contains the modified MAC address of the Ethernet interface
F.Is allocated from the unicast address space
A.port tunneling on the Ethernet subinterface
B.VLAN tunneling on the Ethernet trunk
C.port tunneling on the Ethernet interface
D.VLAN tunneling on the Ethernet VLAN subinterface
E.port tunneling on the Ethernet trunk
A.Tunnel label
B.VC-label
C.5-byte ATM header
D.Payload
E.4 byte ATM header
F.Support for 30 packed cells
A.In Anycast RP, two or more RPs are configured with the same IP address on loopback interfaces.
B.Anycast RP provides redundancy and load-sharing capabilities.
C.Routers with Anycast RP can be configured statically (loopback 1.1.1.1)with the command ip pim rp-address 1.1.1.1
D.Routers with Anycast RP can be configured statically (loopback 1.1.1.1)with the command ip rp-address pim 1.1.1.1
E.Routers with Anycast RP can be configured statically (loopback 1.1.1.1)with the command ip anycast-rp pim 1.1.1.1
A.PPP over Ethernet
B.Cisco Express forwarding
C.MPLS traffic Engineering
D.IS-IS routing
E.Unicast Reverse Path Forwarding(uRPF)
A.Version
B.Label
C.COS/EXP
D.TTL
E.S flag
A.It adds the VPN label into the top label in the MPLS label stack
B.It replaces the top label in the MPLS label stack with a VPN label and propagates
C.It replaces the bottom label in the MPLS label stack with a VPN label and propagates
D.It removes the top label in the MPLS label stack and does a Layer 3 lookup on underlying IP packets
E.None of above
最新试题
Which three statements about MPLS traffic engineering (MPLS TE) are true? ()
Which two statements about Layer 3 MPLS VPN are true?()
There are two cabling schemes to choose from when implementing a Cisco CRS-1 multishelf system:single-module cabling and multimodule cabling. What is the maximum capacity of the LCCs that aresupported in multimodule cabling?()
Which two routers support cable access?()
MPLS label mapping on an LSR is displayed by which IOS command?()
Which tree of these are types of Ethernet Virtue Connections (EVCs) in the MEF concept?()
What layer of the TMN (telecommunications management network) model does CTM fit into?()
Which configuration prevents traffic that is sourced from the unique local address scope to be sent out ofthe link to the upstream service provider?()
How many messages does internet Key Exchange use to negotiate SA characteristics when running inmain mode?()
Which four statements about Ethernet virtual circuit (EVC) infrastructure are true? ()