On a newly installed router, the following access list is added to the HSSI interface for incoming traffic:Access-list 101 permit tcp any 10.18.10.0 0.0.0.255 eq tcp
What is the effect of the "any" keyword in the above access list?（）
A. check any of the bits in the source address
B. permit any wildcard mask for the address
C. accept any source address
D. check any bit in the destination address
E. permit 255.255.255.255 0.0.0.0
F. accept any destination
您可能感兴趣的试卷
你可能感兴趣的试题
On your newly installed router, you apply the access list illustrated below to interface Ethernet 0 on a Cisco router. The interface is connected to the 192.168.1.8/29 LAN.
access-list 123 deny tcp 192.168.166.18 0.0.0.7 eq 20 any
access-list 123 deny tcp 192.168.166.18 0.0.0.7 eq 21 any
How will the above access lists affect traffic?（）
A. All traffic will be allowed to exit E0 except FTP traffic.
B. FTP traffic from 192.168.166.19 to any host will be denied.
C. FTP traffic from 192.168.166.22 to any host will be denied.
D. All traffic exiting E0 will be denied.
E. All FTP traffic to network 192.168.166.18/29 from any host will be denied.
A. TestKingB> telnet
B. TestKingB > ping
C. TestKingB > trace
D. TestKingB > show ip route
E. TestKingB > show interface
F. TestKingB > show cdp neighbors
A. ping
B. trace
C. show ip route
D. show interface
E. show cdp neighbors
A. Serial 0 is up, line protocol is up
B. Serial 0 is up, line protocol is down
C. Serial 0 is down, line protocol is down
D. Serial 0 is down, line protocol is up
E. Serial 0 is administratively down, line protocol is down
F. Serial 0 is administratively down, line protocol is up
There is a connectivity problem between the serial 0/0 interface of router TESTKING1 and the serial 0/0 interface of TESTKING2. A leased line point to point circuit is installed between these two routers. The output from the "show interface serial 0/0" command is displayed below for each of these routers:
From your observations of the above exhibit, what is the underlying cause of the problem?（）
A. The loopback is not set.
B. The serial cable is faulty.
C. The subnet mask is not configured properly.
D. The IP address is not configured properly.
E. The Layer 2 frame types are not compatible.
F. The keepalive setting is not configured properly.
The relevant configuration files for the TestKing1 and TestKing2 routers are displayed below:
With due consideration to the command outputs, which of the following reasons would you attribute the connectivity problem between the two routers?（）
A. The authentication needs to be changed to PAP for both routers.
B. The serial IP addresses of routers are not on the same subnet.
C. The username/password combination is incorrectly configured.
D. The router names are incorrectly configured.
A. ICMP echo request
B. Information interrupt request
C. Timestamp reply
D. Source quench
E. None of the above
The Testking router is running RIP as the routing protocol, and the IP routing table is displayed below:
Gateway of last resort is 10.1.2.2 to network 0.0.0.0
10.0.0.0/24 is subnetted, 2 subnets
R 10.1.3.0 [120/1] via 10.1.2.2, 00:00:00, Serial0/0
C 10.1.2.0 is directly connected, Serial0/0
C 10.1.5.0 is directly connected, Serial0/1
C 10.1.6.0 is directly connected, FastEthernet0/0
R* 0.0.0.0/0 [120/1] via 10.1.5.5, 00:00:00, Serial0/1
Based on the output above, if an administrator pings host 10.1.8.5 from host
10.1.6.100, how will the router TestkingA process the ICMP packets?（）
A. The packets will be discarded.
B. The packets will be routed out the S0/0 interface.
C. The packets will be routed out the S0/1 interface.
D. The packets will be routed out the Fa0/0 interface.
E. The packets will be routed through the 10.1.2.2 gateway.
A. duplex mismatch
B. a routing loop
C. trunking mode mismatch
D. improperly configured root bridge
E. improperly configured static VLAN
While troubleshooting connectivity issues, you log into a remote router. From there,you wish to see the layer 1 and layer 2 status of the interface.
Which of the following IOS commands would you issue to check the current IP addressing, as well as theyer 1 and layer 2 status of an interface?（）
A. TK1# show version
B. TK1# show protocols
C. TK1# show interfaces
D. TK1# show controllers
E. TK1# show ip interface
F. TK1# show startup-config
最新试题
Which of the following correctly describe steps in the OSI data encapsulation process?（）
Five minutes after issuing the show running-config command, a technician enters the command again and notices that several access list statements have been altered. Because of this, the technician believes that the router is being configured by an unknown person through Telnet. Before changing the router passwords, the technician would like to discover if anyone is connected to the router by Telnet and stop them from making further changes.Which commands will accomplish these options?（）
Which connections allow the use of full-duplex Ethernet?（）
Given a subnet mask of 255.255.255.224, which of the following addresses can be assigned to network hosts?（）
TestKing.com has allocated the IP add 199.144.27.0 is its network, to provide flexibility for the LAN design, a subnet mask of 255.255.255.240 has been chosen. Which of the following address can be assigned to LAN on the resulting subnets.（）
Which of the following describe router functions?（）
What is the subnetwork address for a host with IP address 201.100.5.68/28?（）
All WAN links is side the TestKing.com network use PPP with for authentication security. Which command will display the CHAP authentication process as it occurs between two routers in the network?（）
New switches have been purchased for a network upgrade. The objective for the network design emphasizes efficient, error-free transport instead of fast transport.Which switching mode should be configured on the new switches to provide error-free transport to the network? （）
Which of the following options lists the steps in PPP session establishment in the correct order?（）