You need to design router redundancy on the Company network.
Which three protocols could be chosen for IP routing redundancy to protect against first-hop router failure？（）
A. GLBP
B. ICMP
C. MSTP
D. HSRP
E. VRRP
F. NHRP
您可能感兴趣的试卷
你可能感兴趣的试题
Router R1 and R2 are both configured for HSRP.
Which two statements about the HSRP priorities of these two routers are true？（）
A. To assign the HSRP router priority in a standby group， the standby group-number priority priority-value global configuration command must be used.
B. The default priority of a router is zero （0）.
C. The no standby priority command assigns a priority of 100 to the router.
D. Assuming that preempting has also been configured， the router with the lowest priority in an HSRP group would become the active router.
E. When two routers in an HSRP standby group are configured with identical priorities， the router with the highest configured IP address will become the active router.
Which first-hop redundancy solution listed would supply Company clients with MAC address0000.0C07.AC0A for group 10 in response to an ARP request for a default gateway？（）
A. IRDP
B. Proxy ARP
C. GLBP
D. HSRP
E. VRRP
F. IP Redirects
You work as a network technician at Company. Your boss， Mrs. ， is interested in
GLBP. In particular， she wants to know the multicast address that this protocol uses.
What should you tell her？ （）
A. 224.0.0.100
B. 224.0.0.1
C. 224.0.0.102
D. 224.0.0.10
E. 224.0.0.101
F. None of the other alternatives apply
A. IRDP
B. SNMP
C. HSRP
D. VRRP
A. Proxy ARP
B. HSRP
C. IRDP
D. VRRP
E. GLBP
In the hardware address 0000.0c07.ac0av，
what does 07.ac represent？ （）
A. HSRP well-known physical MAC address
B. Vendor code
C. HSRP router number
D. HSRP group number
E. HSRP well-known virtual MAC address
A. per host using a round robin scheme
B. per host using a strict priority scheme
C. per session using a round robin scheme
D. per session using a strict priority scheme
E. per GLBP group using a round robin scheme
F. per GLBP group using a strict priority scheme
Which one of the statements below correctly describes the Virtual Router Redundancy Protocol （VRRP），
which is being used in the Company network to provide redundancy？（）
A. A VRRP group has one active and one or more standby virtual routers.
B. A VRRP group has one master and one or more backup virtual routers.
C. A VRRP group has one master and one redundant virtual router.
D. None of the other alternatives apply
HSRP has been configured between two Company devices.
What kind of message does an HSRP configured router send out every 3 seconds？（）
A. Retire
B. Coup
C. Resign
D. Send
E. Hello
To protect against first-hop router failure， four protocols were developed to ensure IP routing redundancy.
Which of the following are they？（）
A. HSRP
B. IRDP
C. ICMP
D. VRRP
E. MSTP
F. GLBP
最新试题
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Which statement is correct about RSTP port roles？（）
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）