Switch 1 was configured as shown below：
Based on the output shown above，
which statement is true？（）
A.IP traffic matching access list is forwarded through VLANs 5-10.
B.All VLAN traffic in VLANs 5-10 that match access list will be forwarded， and all else will be dropped.
C.IP traffic matching VLAN list 5-10 will be forwarded， and all other traffic will be dropped.
D.All VLAN traffic matching VLAN list 5-10 will be forwarded， and all traffic matching access list is dropped.
E.None of the other alternatives apply
您可能感兴趣的试卷
你可能感兴趣的试题
The following was configured on a switch：
Switch（config） # spanning-tree portfast bpdufilter default
What is the effect of this configuration command？（）
A.If BPDUs are received by a port configured for PortFast， they are ignored and none are sent.
B.The command will enable BPDU filtering on all ports regardless of whether they are configured for BPDU filtering at the interface level.
C.If BPDUs are received by a port configured for Portfast， the port will transition to forwarding state.
D.If BPDUs are received by a port configured for PortFast， then PortFast is disabled and the BPDUs are processed normally.
E.None of the other alternatives apply.
An SVI has been configured on a device.
Which two statements are true about a switched virtual interface （SVI）？（）
A.An SVI is normally created for the default VLAN （VLAN1） to permit remote switch administration.
B.Multiple SVIs can be associated with a VLAN.
C.SVI is another name for a routed port.
D.An SVI is created by entering the no switchport command in interface configuration mode.
E.An SVI provides a default gateway for a VLAN.
The following output was displayed on a switch.
Study the exhibit carefully. The administrator is verifying that a CEF FIB entry exists to destination network 192.168.150.0. Given the output generated by the "show ip cef" and "show adjacency detail" commands，
which three statements are true？ （）
A.The "valid cached adjacency" entry indicates that CEF will put all packets going to such an adjacency to the next best switching mode.
B.The number 003071506800 is the MAC address of the source IP address.
C.There is a valid CEF entry for the destination network 192.168.150.0.
D.The number 003071506800 is the MAC address of the 192.168.199.3 next hop IP address.
E.The counters （0 packets， 0 bytes） indicate a problem with the 192.168.199.3 next hop IP address.
F.There is an adjacency for the 192.168.199.3 next hop IP address.
You work as a network technician at. Your boss， Mrs. ， is interested in the Spanning Tree Protocol timers.
What can you tell her regarding the default STP timers？ （）
A.The hello time is 5 seconds.
B.The forward delay is 10 seconds.
C.The hello time is 2 seconds.
D.The forward delay is 15 seconds
E.The max_age timer is 15 seconds.
F.The hello time is 10 seconds.
G.The max_age timer is 20 seconds.
H.The forward delay is 20 seconds.
I.The max_age timer is 30 seconds.
A switch port on TK1 is being configured to support 802.1Q trunking.
Which of the following are true about 802.1Q trunking？（）
A.Both switches must be in the same VTP domain.
B.The encapsulation type of both ends of the trunk does not have to match.
C.The native VLAN on both ends of the trunk must be VLAN 1.
D.802.1Q trunking can only be configured on a Layer 2 port.
E.In 802.1Q trunking， all VLAN packets are tagged on the trunk link， except the native VLAN.
A.forwarding information base
B.adjacency tables
C.neighbor tables
D.caching tables
E.route tables
A.Address Resolution Protocol （ARP）
B.PDU header rewrite
C.NetFlow switching
D.hello packet exchange
A.Switch（config-if）#spanning-tree guard root
B.Switch（config-if）#spanning-tree portfast
C.Switch（config-if）#switchport mode trunk
D.Switch（config-if）#switchport mode access
A port in a redundant topology is currently in the blocking state and is not receiving BPDUs. To ensure that this port does not erroneously transition to the forwarding state，
which command should be configured to satisfy the requirement？（）
A.Switch（config）#spanning-tree loopguard default
B.Switch（config-if）#spanning-tree bdpufilter
C.Switch（config）#udld aggressive
D.Switch（config-if）#spanning-tree bpduguard
A.spanning-tree guard root
B.spanning-tree portfast bpduguard default
C.spanning-tree bpduguard enable
D.spanning-tree bpdufilter enable
E.spanning-tree portfast bpdufilter default
最新试题
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command， which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true？（）
Which two statements are true when the extended system ID feature is enabled？ （）
Which statement is correct about the use of the virtual interface on a WLC ？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）