A.150.150.0.0
B.150.150.0.8
C.150.150.8.0
D.150.150.16.0
您可能感兴趣的试卷
你可能感兴趣的试题
A.Network A - 172.16.3.48/26
B.Network A - 172.16.3.128/25
C.Network A - 172.16.3.192/26
D.Link A - 172.16.3.0/30
E.Link A - 172.16.3.40/30
F.Link A - 172.16.3.112/30
The switches shown in the diagram, Core and Core2, are both Catalyst 2950s. The addressing scheme for each company site is as follows:Router Ethernet port - 1st usable addressCore - 2nd usable addressCore2 - 3rd usable addressFor this network, which of the following commands must be configured on Core2 to allow it to be managed remotely from any subnet on the network? ()
A.Core2(config)# interface f0/0 Core2(config-if)# ip address 192.168.1.10 255.255.255.248
B.Core2(config)# interface vlan 1 Core2(config-if)# ip address 192.168.1.11 255.255.255.248
C.Core2(config)# line con 0 Core2(config-line)# password cisco
D.Core2(config)# line vty 0 4 Core2(config-line)# password cisco
E.Core2(config)# ip default-gateway 192.168.1.9
F.Core2(config)# ip route 0.0.0.0 0.0.0.0 192.168.1.8
A.a primary route,stored in the routing table
B.a backup route,stored in the routingt able
C.a backup route,stored in the topology table
D.A primary route,stored in the topology table
A.子网掩码
B.源网络地址
C.目的网络地址
D.下一跳地址
A.应用层
B.表示层
C.会话层
D.传输层
E.网络层
F.链路层
G.物理层
A.the session layer
B.the protocol layer
C.the data link layer
D.the access layer
E.the network layer
F.the application layer
A.It supports VLSM.
B.It is used to route between autonomous systems.
C.It confines network instability to one area of the network.
D.It increases routing overhead on the network.
E.It allows extensive control of routing updates.
F.It is simpler to configure than RIP v2.
A.Router C will use ICMP to inform Host 1 that Host 2 cannot be reached
B.Router C will use ICMP to inform Router B that Host 2 cannot be reached
C.Router C will use ICMP to inform Host 1, Router A, and Router B that Host 2 cannot be reached
D.Router C will send a Destination Unreachable message type
E.Router C will send a Router Selection message type
F.Router C will send a Source Quench message type
A.RIPng
B.OSPFv3
C.IS-IS for IPv6
D.static
最新试题
在配置路由器时,网络技术人员想要命名路由器。输入hostname 命令后,技术人员会看到下列哪一项提示?()
请参见图示。已启用路由器的NAT 功能供PC 访问Internet。可以为路由器接口S0/0/0分配下列哪一个IP 地址?()
请参见图示。电缆1和电缆2分别按照特定的物理层要求接线。哪三个网段使用电缆2?()
路由器使用哪一项信息来确定源主机和目的主机之间的路径?()
请参见图示。网络中的主机A 正在向主机B 发送数据段。有关所交换的数据段的流量控制如图所示。下列关于此通信的陈述,哪两项是正确的?()
请参见图示。图中所示路由表所属的PC 已正确配置。IP 地址192.168.1.254属于哪一个网络设备或接口?()
请参见图示。在网络中,PC1向PC2发送了一条消息。PC2收到的帧如图所示。该帧中的哪一信息确定了正确的目的应用程序?()
要将数据包发送到远程网络,应使用哪种设备?()
OSI 哪一层可提供有序的数据重构服务?()
请参见图示。网络中的所有设备均使用默认配置。此拓扑中存在多少个广播域?()