A. Incorrect VTP domain
B. Incorrect VTP password
C. Incorrect VTP mode
D. Incorrect VTP configuration revision
您可能感兴趣的试卷
你可能感兴趣的试题
A. Clear the MAC address table in the switch.
B. Clear the ARP cache in the switch.
C. Clear the ARP cache in the end devices.
D. Clear the ARP cache in the application servers.
A.Forwarding Address
B.External Route
C.Reference Link-State ID
D.Option
E.Prefix Options
A. The trunking configuration mode on Switch1 is set to Off.
B. The trunking configuration mode on the other end is set to On.
C. The trunking configuration mode on the other end is set to Desirable.
D. Cisco Discovery Protocol is not running on the other end.
E. There is a VTP domain name mismatch.
F. Switch1 does not support 802.1Q
A.It allows the standby RP to take control of the device after a hardware or software fault on the active RP.
B.It is a Layer 3 function that works with SSO to minimize the amount of time a network is unavailable tousers following a switchover.
C.It is supported by the implementation of EIGRP, OSPF, RIPv2, and BGP protocols.
D.It synchronizes startup configuration, startup variables, and running configuration.
E.The main objective of NSF is to continue forwarding IP packets following a switchover.
F.Layer 2 802.1w or 802.1s must be used, as 802.1d cannot process the Layer 2 changes.
G.Routing protocol tuning parameters must be the same as the NSF parameters, or failover will beinconsistent.
A. The VSS switch must be the root bridge for all VLANs and is automatically designated
B. The VSS switch is defined in RFC 4318 as a managed object
C. The PAgP+ or LACP protocols are used to maintain the operational state of the VSS devices
D. A VSS interoperates with a virtual port channel
E. The 802.1Q or ISL protocols are used to maintain the operational state of the VSS devices
F. A VSS increases the size of the spanning-tree domain
A.telnet 11.1.1.4 /vrf-source red
B.telnet 11.1.1.4 source /vrf red
C.telnet 11.1.1.4 /source vrf red
D.telnet 11.1.1.4 /vrf red
E.telnet 11.1.1.4 vrf red
A.all routes in the routing table
B.only the IGP and BGP routes in the routing table
C.only the BGP routes in the routing table
D.only the IGP routes in the routing table
A.ip vrf CCIE
B.ipv6 vrf CCIE
C.vrf definition CCIE
D.ipv6 vrf definition CCIE
Refer to the exhibit. From the MAC addresses shown in the command output, to which two ports is the multicast stream 225.230.57.199 being forwarded on this switch? ()
A. Fa7/28
B. Fa7/20
C. Gi3/7
D. Fa4/2
E. Fa4/14
F. Fa4/38
G. Fa6/28
H. Fa5/7
A.0
B.1
C.255
D.256
最新试题
In PIM-SM what control plane signaling must a multicast source perform before it begins to send multicasttraffic to a group?()
Which three options are valid ways to filter routes from a BGP peer?()
Which multicast address is reserved for cisco-rp-discovery?()
Which command is used to enable SSM with the range 232.0.0.0 - 255.0.0.0?()
Which of these best describes the actions taken when a VTP message is received on a switch configuredwith the VTP mode "transparent"?()
Based on the exhibit presented. What will be the objective of this route map when applied to traffic passing through a router?()
All of these are fundamental building blocks of differentiated services Traffic Conditioner Block exceptwhich one?()
Which of these statements about penultimate hop popping are true?()
Based on the output provided in the exhibit, to which address or location will the router forward a packet sent to 192.168.32.1?()
In order to configure two routers as anycast RPs, which of these requirements, af a minimum, must besatisfied?()