A.Source Specific Multicast and IGMPv2
B.Announcing multicast sources to BGP speakers
C.Anycast RP
D.Intradomain multicast routing
您可能感兴趣的试卷
你可能感兴趣的试题
Refer to the exhibit. Look at the command output. Assume that there is no other path， and the configuration is correct. What would be the consequences of this situation？（）
A. Users in SW1 can ping SW2 but not vice versa.
B. Users in SW2 can ping SW1 but not vice versa.
C. Users in SW1 and SW2 can ping each other.
D. Users in SW1 and SW2 cannot ping each other.
A.to prevent multicast packets from looping
B.to prevent PIM packets from looping
C.to instruct PIM where to send a （*， G） or （S， G） join message
D.to prevent multicast packets from looping and to instruct PIM where to send a （*， G） or （S， G） joinmessage
A.232.0.0.0/8
B.239.0.0.0/8
C.232.0.0.0/4
D.FF3x：：/32
E.FF2x：：/32
F.FF3x：：/16
Refer to the exhibit. Look at the command output. What would be the most probable reason for this port-ID mismatch？（）
A. spanning-tree misconfiguration
B. speed mismatch configuration
C. cabling problem
D. configuration problem
A.PIM-SM
B.PIM-DM
C.PIM-SSM
D.DVMRP
A. Incorrect VTP domain
B. Incorrect VTP password
C. Incorrect VTP mode
D. Incorrect VTP configuration revision
A. Clear the MAC address table in the switch.
B. Clear the ARP cache in the switch.
C. Clear the ARP cache in the end devices.
D. Clear the ARP cache in the application servers.
A.Forwarding Address
B.External Route
C.Reference Link-State ID
D.Option
E.Prefix Options
A. The trunking configuration mode on Switch1 is set to Off.
B. The trunking configuration mode on the other end is set to On.
C. The trunking configuration mode on the other end is set to Desirable.
D. Cisco Discovery Protocol is not running on the other end.
E. There is a VTP domain name mismatch.
F. Switch1 does not support 802.1Q
A.It allows the standby RP to take control of the device after a hardware or software fault on the active RP.
B.It is a Layer 3 function that works with SSO to minimize the amount of time a network is unavailable tousers following a switchover.
C.It is supported by the implementation of EIGRP， OSPF， RIPv2， and BGP protocols.
D.It synchronizes startup configuration， startup variables， and running configuration.
E.The main objective of NSF is to continue forwarding IP packets following a switchover.
F.Layer 2 802.1w or 802.1s must be used， as 802.1d cannot process the Layer 2 changes.
G.Routing protocol tuning parameters must be the same as the NSF parameters， or failover will beinconsistent.
最新试题
Which message type is constructed and sent from an MSDP router to its MSDP peers when it receives a PIM register message knowing that the MSDP router is also configured as an RP for the PIM domain？（）
An expanding company is deploying leased lines between its main site and two remote sites. Thebandwidth of the leased lines is 128kb/s each，terminated on different serial interfaces on the main router.These links are used for combined VOIP and data traffic. The network administrator has implemented a VOIP solution to reduce costs，and has therefore reserved sufficient bandwidth in a low latency queue oneach interface for the VOIP traffic. Users now complain about bad voice quality although no drops areobserved in the low latency queue. What action will likely fix this problem？（）
Which of these best describes the actions taken when a VTP message is received on a switch configuredwith the VTP mode "transparent"？（）
Which protocol and port have been assigned by IANA for RADIUS authentication？（）
Based on the output provided in the exhibit， to which address or location will the router forward a packet sent to 192.168.32.1？（）
Which two statements are true about RED？（）
What is true about Unicast RPF in strict mode？（）
Which multicast address is reserved for cisco-rp-discovery？（）
Which of the following is true about the MPLS header and its EXP field size？（）
What is the command to configure RSVP to reserve up to one-tenth of a Gigabit link，but only allow eachindividual flow to use 1 MB/s？（）