A.Do not enable all the signatures at the same time.
B.Do not enable the ICMP signature.
C.Disable the Zone-Based Policy Firewall because it is not compatible with Cisco IOS IPS.
D.Disable CEF because it is not compatible with Cisco IOS IPS. .
您可能感兴趣的试卷
你可能感兴趣的试题
A.It is a Cisco proprietary protocol.
B.It runs on TCP port 59. .
C.Authentication and authorization are done at different stages.
D.TACACS+ encrypts the entire body of the packet, but leaves a standard TACACS+ header.
E.It is an industry standard protocol.
F.TACACS+ encrypts both the entire body of the packet and the TACACS+ header.
A.it is used for load balancing in bidirectional PIM
B.it is used for redundancy in bidirectional PIM
C.it is used for redundancy in PIM-SM
D.it is used for load balancing in PIM-SM
Refer to the exhibit. Look at the command output. What can you use to prevent this behavior? ()
A. UDLD (UniDirectional Link Detection)
B. spanning-tree loopguard
C. VTP mode transparent
D. switchport mode desirable
A.Membership Query
B.Membership Report
C.Membership Delay
D.Backward Compatible IGMPv1 Report Message
A.Source Specific Multicast and IGMPv2
B.Announcing multicast sources to BGP speakers
C.Anycast RP
D.Intradomain multicast routing
Refer to the exhibit. Look at the command output. Assume that there is no other path, and the configuration is correct. What would be the consequences of this situation?()
A. Users in SW1 can ping SW2 but not vice versa.
B. Users in SW2 can ping SW1 but not vice versa.
C. Users in SW1 and SW2 can ping each other.
D. Users in SW1 and SW2 cannot ping each other.
A.to prevent multicast packets from looping
B.to prevent PIM packets from looping
C.to instruct PIM where to send a (*, G) or (S, G) join message
D.to prevent multicast packets from looping and to instruct PIM where to send a (*, G) or (S, G) joinmessage
A.232.0.0.0/8
B.239.0.0.0/8
C.232.0.0.0/4
D.FF3x::/32
E.FF2x::/32
F.FF3x::/16
Refer to the exhibit. Look at the command output. What would be the most probable reason for this port-ID mismatch?()
A. spanning-tree misconfiguration
B. speed mismatch configuration
C. cabling problem
D. configuration problem
A.PIM-SM
B.PIM-DM
C.PIM-SSM
D.DVMRP
最新试题
What is the command to configure RSVP to reserve up to one-tenth of a Gigabit link,but only allow eachindividual flow to use 1 MB/s?()
Which command is used to enable SSM with the range 232.0.0.0 - 255.0.0.0?()
Which of the following is true about the MPLS header and its EXP field size?()
Which two statements about SA caching are true?()
Which three message types are valid PIMv2 message types?()
What is true about Unicast RPF in strict mode?()
Which protocol and port have been assigned by IANA for RADIUS authentication?()
What is also called Type 0 authentication in OSPF on Cisco Routers?()
Two routers configured to run BGP have been connected to a firewall, one on the inside interface and one on the outside interface. BGP has been configured so the two routers should peer, including the correctBGP session endpoint addresses and the correct BGP session hop-count limit EBGP multihop. What is agood first test to see if BGP will work across the firewall?()
Which types of prefixes will a router running BGP most likely advertise to an IBGP peer, assuming it is notconfigured as a route reflector?()