Which configuration would&...

单项选择题Which configuration would make an IP SLA probe use a precedence value of 3？（）

A.ip sla 1  icmp-echo 1.1.1.1 tos 12
B.ip sla 1  icmp-echo 1.1.1.1 tos 96
C.ip sla 1  icmp-echo 1.1.1.1 precedence 3
D.ip sla 1  icmp-echo 1.1.1.1 dscp 12

点击查看答案

您可能感兴趣的试卷

你可能感兴趣的试题

1.单项选择题On a router that is configured with multiple IP SLA probes， which command can be used to manage the CPU load that was created by the periodic probing？（）

A.ip sla monitor low-memory
B.ip sla group schedule
C.ip sla reaction-trigger
D.ip sla enable timestamp

点击查看答案

2.单项选择题 Refer to the exhibit. In this network， R1 is configured not to perform autosummarization within EIGRP. What routes will R3 learn from R2 through EIGRP？（）

A. 172.30.1.0/24 and 10.1.2.0/24；EIGRP only performs autosummarization at the edge between two major networks.
B. 172.30.0.0/16 and 10.1.2.0/24；R2 will perform autosummarization although R1 will not.
C. Since R2 is configured without autosummarization， it will not propagate the 172.30.1.0/24 route.
D. 172.30.0.0/8 and 10.0.0.0/8.

点击查看答案

3.单项选择题 Refer to the exhibit. In this network， R1 has been configured to advertise a summary route， 192.168.0.0/22， to R2. R2 has been configured to advertise a summary route， 192.168.0.0/21， to R1. Both routers have been configured to remove the discard route （the route to null created when a summary route is configured） by setting the administrative distance of the discard route to 255. What will happen if R1 receives a packet destined to 192.168.3.1？（）

A. The packet will loop between R1 and R2.
B. It is not possible to set the administrative distance on a summary to 255.
C. The packet will be forwarded to R2， where it will be routed to null0.
D. The packet will be dropped by R1， since there is no route to 192.168.3.1.

点击查看答案

4.单项选择题You are the network administrator of a small Layer 2 network with 50 users. Lately， users have beencomplaining that the network is very slow. While troubleshooting， you notice that the CAM table of yourswitch is full， although it supports up to 12， 000 MAC addresses. How can you solve this issue and preventit from happening in the future？（）

A.Upgrade the switches
B.Configure BPDU guard
C.Configure VLAN access lists
D.Configure port security
E.Configure Dynamic ARP inspection

点击查看答案

5.单项选择题Two routers configured to run BGP have been connected to a firewall， one on the inside interface and one on the outside interface. BGP has been configured so the two routers should peer， including the correct BGP session endpoint addresses and the correct BGP session hop-count limit （EBGP multihop）. What is a good first test to see if BGP will work across the firewall？（）

A. Attempt to TELNET from the router connected to the inside of the firewall to the router connected to the outside of the firewall. If telnet works， BGP will work， since telnet and BGP both use TCP to transport data.
B. Ping from the router connected to the inside interface of the firewall to the router connected to the outside interface of the firewall. If you can ping between them， BGP should work， since BGP uses IP to transport packets.
C. There is no way to make BGP work across a firewall without special configuration， so there is no simple test that will show you if BGP will work or not， other than trying to start the peering session.
D. There is no way to make BGP work across a firewall.

点击查看答案

6.多项选择题You are the network administrator of a medium-sized company， and users are complaining that they cannotsend emails to some organizations. During your troubleshooting， you notice that your DNS MX record isblacklisted by several public blacklist filters. After clearing these listings for your IP address， and assumingthat your email server has the right virus protection in place， what are two possible solutions to prevent thisfrom happening in the future？（）

A.Change your Internet provider.
B.Change your public IP address.
C.Allow the email server to send traffic only to TCP port 25.
D.Put your email server in a DMZ.
E.Use a separate public IP address for your email server only.

点击查看答案

7.单项选择题While deploying a new switch， you accidently connect ports 3/12 and 3/18 together， creating a loop. STP detected it and placed port 3/18 in blocking mode. Why did STP not place port 3/12 in blocking mode instead？（）

A. Port 3/12 was already up and forwarding before the loop was created.
B. Port priority is based on lowest priority and lowest port number.
C. You connected the wire on port 3/18 last.
D. None of the above， it is purely random.

点击查看答案

8.单项选择题After applying a new ACL on a device， its CPU utilization rose significantly and many messages startingwith "%SEC-6-IPACCESSLOG" appeared on the Syslog server.What can be done to resolve this situation？（）

A.Increase memory allocation for ACLs.
B.Remove all entries from the ACL and use a single permit ip any any statement.
C.Remove the log keyword from each ACL entry.
D.Reboot the device after the ACL has been applied.

点击查看答案

9.单项选择题You deployed new fibers in your network to replace copper spans that were too long. While reconnecting the network， you experienced network problems because you reconnected wrong fibers to wrong ports. What could you do to prevent this type of problem in the future， particularly when connecting and reconnecting fiber pairs？（）

A. Only use fiber in pairs.
B. Configure root guard on your switches.
C. Do not use fiber but use copper.
D. Configure UDLD to prevent one-way link conditions.

点击查看答案

10.单项选择题Which feature would prevent guest users from gaining network access by unplugging an IP phone andconnecting a laptop computer？（）

A.IPSec VPN
B.SSL VPN
C.port security
D.port security with statically configured MAC addresses
E.private VLANs

点击查看答案