Refer to the exhibit. How would you get the 1.1.1.1 network into the OSPF database? ()
A. Configure RTA as an ASBR
B. Redistribute connected routes on RTA into OSPF
C. Set up a virtual link between area 1 and area 0
D. Set up a virtual link between area 1 and area 2
E. Add a static route into RTB and enter it into OSPF
F. Place a network 1.1.1.0 0.0.0.0 command into RTB
G. Set up a unique router ID on RTA using an RFC 1918 address
H. Change area 0 on RTB to area 1
您可能感兴趣的试卷
你可能感兴趣的试题
A.disable Zone-Based Firewall as the two features are not compatible
B.disable Cisco Express Forwarding as the two features are not compatible
C.generate a certificate and export on Cisco.com to receive a signature update
D.import the public RSA key from the Cisco IPS team that allows the router to verify that a signatureupdate (which was signed by this key) comes from Cisco
A. Add the command: router eigrp 1 traffic-share voice interface fast 0/0
B. Reconfigure EIGRP to recognize voice packets
C. Remove the variance from the configuration
D. Reconfigure the VoIP system to use RTP sequence number headers
E. Use an H '323 gatekeeper for your VoIP system to negotiate an H'245 uneven packet buffer
F. Reconfigure EIGRP to version 2
A.show ip pim rendez-vous
B.show ip rpf rp mapping
C.show ip pim rp mapping
D.show ip pim rp info
E.show ip pim
A.it enables PIM BSR
B.it makes the router an Auto-RP mapping agent
C.it advertises the router as an RP with Auto-RP
D.it makes the router an Auto-RP client
A.It will send the join only to the neighbor with the highest IP address.
B.It will send the join only to the neighbor with the lowest IP address.
C.It will send the join in a round-robin fashion across all neighbors.
D.It will send the join to all neighbors.
A.2001:db8:3811::1
B.2001:db8:3811::2323
C.2001:db8:3811::0130
D.2001:db8:3811::3
E.2001:db8:3811::6
A.Flooding paths and redundancy
B.Amount of routing information in the OSPF area or routing domain
C.Number of routers with Cisco Express Forwarding enabled
D.Number of neighbor adjacencies
E.Other routing protocols in use
F.OSPF timer reconstruction negotiation
G.Redistribution with BGP neighbors
H.Redistribution with other IGP routing protocols, such as RIP or EIGRP
A. BGP peers must be Layer 2-adjacent
B. EBGP multihop is not configured
C. The firewall is not configured to allow IP protocol 89
D. The firewall is not configured to allow UDP 179.
Refer to the exhibit. Users on the 199.155.24.0 network are unable to reach the 172.16.10.0 network. What is the most likely solution?()
A. Router ISP1 should be configured to peer with router B
B. Router ISP2 should be configured with no synchronization
C. Router ISP1 should be configured with no synchronization
D. Router ISP2 should be configured with no auto-summary.
E. Router ISP1 or IPS2 should be configured with network 176.16.10.0 mask 255.255.255.0
A.It relies on IPv6 to do the fragmenting.
B.It splits the LS Update packet into smaller packets.
C.It splits the LSA into smaller router LSA packets.
D.It produces an error.
最新试题
Choose two commands that are required to enable multicast on a router, when it is known that thereceivers use a specific functionality of IGMPv3.()
Two routers configured to run BGP have been connected to a firewall, one on the inside interface and one on the outside interface. BGP has been configured so the two routers should peer, including the correctBGP session endpoint addresses and the correct BGP session hop-count limit EBGP multihop. What is agood first test to see if BGP will work across the firewall?()
What is also called Type 0 authentication in OSPF on Cisco Routers?()
Which two are differences between IGMPv2 and IGMPv3 reports?()
Spanning Tree Protocol IEEE 802.1 s defines the ability to deploy which of these?()
Which multicast address is reserved for cisco-rp-discovery?()
What is true about Unicast RPF in strict mode?()
On the basis of the network provided in the exhibit, all routers are configured to run EIGRP on all links. If the link between PG-R1 and PG-R2 fails, what is the maximum number of queries PG-R3 will receive for 192.168.1.0/24, assuming that all the packets sent during convergence are transmitted once (there are no dropped or retransmitted packets)?()
What is the correct command to set the router ID for an OSPFv3 process?()
Which command is used to enable SSM with the range 232.0.0.0 - 255.0.0.0?()