A. Administratively shut down the interfaces.
B. Physically secure the interfaces.
C. Configure a virtual terminal password and login process.
D. Enter an access list and apply it to the terminal interfaces using the access-class command.
E. Create an access list and apply it to the terminal interfaces using the access-group command.
您可能感兴趣的试卷
你可能感兴趣的试题
A.multicast
B.broadcast
C.allcast
D.podcast
E.anycast
A.blocking
B.learning
C.disabled
D.forwarding
E.listening
A. Security increases because only the network administrator may change the routing tables.
B. Configuration complexity decreases as network size increases.
C. Routing updates are automatically sent to neighbors.
D. Route summarization iscompued automatically by the router.
E. Routing traffic load is reduced when used in stub network links
F. An efficient algorithm is used to build routing tables,using automatic updates.
G. Routing tables adapt automatically to topology changes.
A. to confine network instability to single areas of the network.
B. to reduce the complexity of router configuration
C. to speed up convergence
D. to lower costs by replacing routers with distribution layer switches
E. to decrease latency by increasing bandwidth
F. to reduce routing overhead
A.complicated header
B.plug-and-play
C.no broadcasts
D.checksums
E.optional IPsec
F.autoconfiguration
A. They are always present in the NAT table.
B. They allow connection to be initiated from the outside.
C. They can be configured with access lists, to allow two or more connections to be initiated from the outside.
D. They require no inside or outside interface markings because addresses are statically defined.
A. RSTP significantly reduces topology reconverging time after a link failure.
B. RSTP expends the STP port roles by adding the alternate and backup roles.
C. RSTP port atates are blocking,discarding,learing,or forwarding.
D. RSTP also uses the STP proprsal-agreement sequence.
E. RSTP use the same timer-baseed process as STP on point-to-point links.
F. RSTP provides a faster transition to the forwarding state on point-to-point links than STP does.
A. NAT protects network security because private networks are not advertised.
B. NAT accelerates the routing process because no modifications are made on the packets.
C. Dynamic NAT facilitates connections from the outside of the network.
D. NAT facilitates end-to-end communication when IPsec is enable.
E. NAT eliminates the need to re-address all host that require extemal access.
F. NAT conserves addresses through host MAC-level multiplexing.
A. SW1#show swithport port-security interface FastEthernet 0/12
B. SW1# show swithport port-secure interface FastEthernet 0/12
C. SW1# show port-secure interface FastEthernet 0/12
D. SW1#show running-config
E. SW1#show port-security interface FastEthernet 0/12
A. when they receive a special token
B. when there is a carrier
C. when they detect no other devices are sending
D. when the medium is idle
E. when the server grants access
最新试题
At which layer of the OSI model dose PPP perform?()
Which cisco ios command can help to determine the timing of various debug events,relative to each other,when you are debugging a complicated router issue?()
Which device might be installed at a branch office to enable and manage an IPsec site-to-site VPN?()
After the show ip route command has been entered,the follwing routes are displayed.Which route will not be entered into the routing table of a neighboring router?()
What is the subnetwork address for a host with the IP address 201.100.5.68/28?()
Which command is used to display the collection of OSPF link states?()
Which Cisco IOS diagnostics command can disrupt the operation of a router under high-load conditions?()
The network administrator cannot to switch 1 over a telnet session,although the hosts attached to switch 1 can ping the interface Fa0/0 of the router.Given the information in the graphic and assuming that the router and switch2 are configured properly,which of the following commands should be issued on switch 1 to correct this problem?()
If all OSPF routers in a single area are configured with the same priority value,what value dose a router use for the ODPF router ID in the absence of a loopback interface?()
At which layer of the OSI model is RSTP used to prevent loops?()