A. Layer 3
B. Layer 4
C. Layer 2
D. Layer 5
您可能感兴趣的试卷
你可能感兴趣的试题
A. show ip ospf lsa database
B. show ip ospf link-state
C. show ip ospf neighbors
D. show ip ospf database
A. show ip access-list
B. show access-list
C. list ip interface
D. show interface
E. show ip interface
A. the switch with the lowest MAC address
B. the switch with the higest MAC address
C. the switch witch the higest IP address
D. the switch with the lowest IP address
A. to provide a mechanism to dynamically assign vlan membership to switch ports
B. to allow traffic to be carried from multiple vlans over a single link between switches
C. to allow native vlan information to be carried over a trunk link
D. to provide a mechanism to manually assign vlan membership to switch ports
E. to allow for managing the additions,deletions,and changes of vlans between switchs
A. service timestamps debug datetime msec
B. show clock detail
C. clock calendar-valid
D. service timestamps log datetime msec
A. source address and subnet mask
B. destination address and wildcard mask
C. source address and wildcard mask
D. destination address and subnet mask
A. Main(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#no shut
B. Main(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation ietf Main(config-if)#no shut
C. Main(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation frame-relay Main(config-if)#authenication chap Main(config-if)#no shut
D. Main(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation ppp Main(config-if)#no shut
A. defines the source IP address that i s used in all broadcast packets on DLCI 202
B. defines the DLCI that is used for all packets that are sent to the 192.168.1.2 IP address
C. defines the destination IP address that is used in all broadcast packets on DLCI 202
D. defines the DLCI on which packets from the 192.168.1.2 IP address are received
A. anycast frames
B. multicast frames
C. broadcast frames
D. unicast frames
A. OSPF and mumber of hops and reliability
B. EIGRP and link cost
C. IS-IS and delay and reliability
D. RIPv2 and number of hops
最新试题
On which options are standard access list based?（）
After the show ip route command has been entered,the follwing routes are displayed.Which route will not be entered into the routing table of a neighboring router?（）
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
Which command is used to display the collection of OSPF link states?（）
Which name describes an IPV6 host-enable tunneling technique that uses IPV4 UDP,does not require dedicated gateway tunnels,and can pass through existing IPV4 NAT gateways?（）
Which IPsec security protocol should be used when confidentiality is required?（）
Which address is the IPV6 all-RIP-routers muticast group address that is used by RIPng as the destaion address?（）
When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?（）
Which statement is true, as relates to classful or classless routing?（）
Which cisco ios command can help to determine the timing of various debug events,relative to each other,when you are debugging a complicated router issue?（）