A. show ip access-list
B. show access-list
C. list ip interface
D. show interface
E. show ip interface
您可能感兴趣的试卷
你可能感兴趣的试题
A. the switch with the lowest MAC address
B. the switch with the higest MAC address
C. the switch witch the higest IP address
D. the switch with the lowest IP address
A. to provide a mechanism to dynamically assign vlan membership to switch ports
B. to allow traffic to be carried from multiple vlans over a single link between switches
C. to allow native vlan information to be carried over a trunk link
D. to provide a mechanism to manually assign vlan membership to switch ports
E. to allow for managing the additions,deletions,and changes of vlans between switchs
A. service timestamps debug datetime msec
B. show clock detail
C. clock calendar-valid
D. service timestamps log datetime msec
A. source address and subnet mask
B. destination address and wildcard mask
C. source address and wildcard mask
D. destination address and subnet mask
A. Main(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#no shut
B. Main(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation ietf Main(config-if)#no shut
C. Main(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation frame-relay Main(config-if)#authenication chap Main(config-if)#no shut
D. Main(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation ppp Main(config-if)#no shut
A. defines the source IP address that i s used in all broadcast packets on DLCI 202
B. defines the DLCI that is used for all packets that are sent to the 192.168.1.2 IP address
C. defines the destination IP address that is used in all broadcast packets on DLCI 202
D. defines the DLCI on which packets from the 192.168.1.2 IP address are received
A. anycast frames
B. multicast frames
C. broadcast frames
D. unicast frames
A. OSPF and mumber of hops and reliability
B. EIGRP and link cost
C. IS-IS and delay and reliability
D. RIPv2 and number of hops
A. dual stack
B. dynamic
C. Teredo
D. Manual 6to4
A. show running-config
B. show processes cpu
C. debug all
D. logging host ip address
最新试题
When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?()
Which Cisco IOS diagnostics command can disrupt the operation of a router under high-load conditions?()
On which options are standard access list based?()
Which IPsec security protocol should be used when confidentiality is required?()
While troubleshooting a network problem,a technician discovers that the current copy of the Cisco IOS is outdated and needs to be updated.Which of the following commands would the technician issue to replace the Cisco router IOS with the newer version?()
Three access ports have been installed and configured to a small office.What term defines the wireless topology?()
After the show ip route command has been entered,the follwing routes are displayed.Which route will not be entered into the routing table of a neighboring router?()
Which encapsulation type is a Frame Relay encapsulation type that is supported by Cisco routers?()
The network administrator cannot to switch 1 over a telnet session,although the hosts attached to switch 1 can ping the interface Fa0/0 of the router.Given the information in the graphic and assuming that the router and switch2 are configured properly,which of the following commands should be issued on switch 1 to correct this problem?()
A router receives information about network 192.168.10.0/24 from multiple sources.What will the router consider the most reliable information about the path to that network?()