A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?()
Router(config)#router ospf 1
Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
A. The process id is configured improperly
B. The OSPF area is configured improperly
C. The network wildcard mask is configured improperly
D. The network number is configured improperly
E. The AS is configured improperly
F. The network subnet mask is configuerd improperly
您可能感兴趣的试卷
你可能感兴趣的试题
A. the IP address of the first Fast Ethernet interface
B. the IP address of the console management interface
C. the highest IP address among its active interfaces
D. the lowest IP address among its active interfaces
E. the priority value until a loopback interface is configured
A. IBSS
B. BSS
C. ESS
D. SSID
The network administrator cannot to switch 1 over a telnet session,although the hosts attached to switch 1 can ping the interface Fa0/0 of the router.Given the information in the graphic and assuming that the router and switch2 are configured properly,which of the following commands should be issued on switch 1 to correct this problem?()
A. Switch1(config)# i nterface fa0 /1 Switch1(config-if)# ip address 192.168.24.3.255.255.255.0
B. Switch1 (config)#interface fa0/1 Switch1 (config-if)# switchport mode trunk
C. Switch 1 (config)# i nterface fa0 /1 Switch1 (config-if)# duplex full Switch1 (config-if)# speed 100
D. Switch1 (config-if)# default-gateway 192.168.24.1
E. Switch1 (config)# line con 0 Switch1(config-line)# password cisco Switch1 (config-line)#login
A. 192.168.252.8 255.255.255.248
B. 192.168.252.8 255.255.255.252
C. 192.168.252.16 255.255.255.240
D. 192.168.252.0 255.255.255.252
E. 192.168.252.16 255.255.255.252
A. debug authentication
B. debug chap ppp
C. debug chap authentication
D. debug ppp authentication
A. Layer 3
B. Layer 4
C. Layer 2
D. Layer 5
A. show ip ospf lsa database
B. show ip ospf link-state
C. show ip ospf neighbors
D. show ip ospf database
A. show ip access-list
B. show access-list
C. list ip interface
D. show interface
E. show ip interface
A. the switch with the lowest MAC address
B. the switch with the higest MAC address
C. the switch witch the higest IP address
D. the switch with the lowest IP address
A. to provide a mechanism to dynamically assign vlan membership to switch ports
B. to allow traffic to be carried from multiple vlans over a single link between switches
C. to allow native vlan information to be carried over a trunk link
D. to provide a mechanism to manually assign vlan membership to switch ports
E. to allow for managing the additions,deletions,and changes of vlans between switchs
最新试题
At which layer of the OSI model is RSTP used to prevent loops?()
If all OSPF routers in a single area are configured with the same priority value,what value dose a router use for the ODPF router ID in the absence of a loopback interface?()
Which statement is true, as relates to classful or classless routing?()
Which command encrypts all plaintext passwords?()
At which layer of the OSI model dose PPP perform?()
Which command is used to display the collection of OSPF link states?()
Which command displays the CHAP authentication process as it occurs between two routers?()
Which cisco ios command can help to determine the timing of various debug events,relative to each other,when you are debugging a complicated router issue?()
When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?()
Which pairing reflects a correct protocol-and-metric relationship?()