A. router(config)# ip route 0.0.0.0 10.1.1.0 10.1.1.1
B. router(config)# ip default-route 10.1.1.0
C. router(config)# ip default-gateway 10.1.1.0
D. router(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1
您可能感兴趣的试卷
你可能感兴趣的试题
A.
B.
C.
D.
E.
F.
A. It is globally enabled by default on Cisco routers.
B. It is globally enabled by default on all routers.
C. It is a proprietary protocol.
D. It is a non-proprietary protocol.
E. It can be used to gather hardware and protocol information about neighbor devices.
A. The Frame Relay encapsulation on the physical interface.
B. The local DLCI on each subinterface.
C. An IP address on the physical interface.
D. The subinterface type as point-to-point.
A.close
B.disable
C.disconnect
D.suspend
E.exit
F.None of the above
The Testking Network consists of the following 5 IP networks:
NETWORK 1: 192.168.10.0/26
NETWORK 2: 192.168.10.64/27
NETWORK 3: 192.168.10.96/27
NETWORK 4: 192.168.10.128/30
NETWORK 5: 192.168.10.132/30
Which of the following routing protocols will support this IP addressing scheme?()
A. RIP version 1
B. RIP version 2
C. IGRP
D. EIGRP
E. OSPF
F. BGP
A. CIDR
B. Split horizon
C. Authentication
D. Classless masking
E. Hold-down timers
F. Multicast routing updates
G. Path Vectoring
You need to implement the use of a routing protocol that meets the following
requirements:
1. Converges quickly
2. Supports VLSM, CIDR, IP, and IPX.
3. Uses minimal bandwidth for routing updates.
Which one of the following routing protocols would be the best choice?()
A. RIPv1
B. RIPv2
C. IGRP
D. OSPF
E. EIGRP
A. RIPv1
B. IGRP
C. EIGRP
D. OSPF
E. IS-IS
F. RIPv2
A. RIPv1
B. EIGRP
C. OSPF
D. IGRP
E. RIPv2
A. IGRP
B. EIGRP
C. RIP v1
D. RIP v2
E. OSPF
F. VTP
G. CDP
最新试题
Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? ()
A Router with a BRI/T interface will be used for an ISDN Connection what other ISDN device is required to complete this connection? ()
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? ()
Identify three valid host addresses in the 192.168.27.0 network with a subnet mask of 255.255.255.240. ()
Which of the following describe router functions?()
New switches have been purchased for a network upgrade. The objective for the network design emphasizes efficient, error-free transport instead of fast transport.Which switching mode should be configured on the new switches to provide error-free transport to the network? ()
A network host is configured as follows: Host IP address: 192.168.16.183 Subnet mask: 255.255.255.224 Default gateway: 192.168.16.190 Which of the following statements describe the network to which this host is attached?()
A technician at TestKing needs to update the network documentation. One of the tasks includes documenting the name of the IOS image file of each router in the network.Which commands could be used to find this information?()
You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?()
Which Frame Relay feature is responsible for transmitting keepalives to ensure that the PVC does not shut down because of inactivity?()