A. Point-to-point
B. Point to multipoint
C. Broadcast
D. Non-broadcast multi-access
您可能感兴趣的试卷
你可能感兴趣的试题
A. All OSPF networks require the use of multiple areas
B. Multiple OSPF areas must connect to area 0
C. Single area OSPF networks must be configured in area 1
D. Areas can be assigned any number from 0 to 63535
E. Area 0 is called the backbone area
F. Each OSPF area need to be configured with a loopback interface
A. It confines network instability to a single area of network.
B. It increases the routing overhead of the network
C. It supports VLSM
D. It routes between Autonomous Systems.
E. It allows extensive control of routing updates
A. 1
B. 64
C. 1562
D. 64000
E. 1500
A. The exchange of advertisement is triggered by a change in the network.
B. All routers exchange routing tables with each other iIn a multipoint network.
C. Packets are routed based upon the shortest path to the destination.
D. Paths are chosen depending on the cost efficiency factor.
E. Every router in an OSPF area is capable of representing the entire network topology.
F. Only the designated router in an OSPF area can represent the entire network topology.
A. Distance vector protocols send the entire routing table to directly connected neighbors.
B. Distance vector protocols are responsible for sending updates to all networks listed in the routing table.
C. Link state protocols are responsible for sending the entire routing table to the whole network.
D. Link state protocols send updates regarding their own links status to all other routers on the network.
A. The IP address of the first Fast Ethernet interface.
B. The IP address of the console management interface.
C. The highest IP address among its active interfaces.
D. The lowest IP address among its active interfaces.
E. There will be no router ID until a loopback interface is configured.
A. Point-to-point
B. Broadcast multicast
C. Nonbroadcast multicast
D. Backbone area 0
E. Virtual Link
A. The RIP route
B. The static route
C. The IGRP route
D. All three will load balance.
A. 15
B. 16
C. 99
D. 255
E. Unlimited
A. Neighbor Table
B. SRF Table
C. RTP Table
D. Topology Table
E. Query Table
F. Dual Table
最新试题
A Class C network address has been subnetted with a /27 mask.Which of the following addresses is a broadcast address for one of the resulting subnets?()
Which of the following if addresses can be assigned to host devices?()
The network 172.12.0.0 needs to be divided into subnets where each subnet has the capacity of 458 IP addresses.What would be the correct subnet mask to accomplish this division keeping the number of subnets at the maximum? ()
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? ()
Five minutes after issuing the show running-config command, a technician enters the command again and notices that several access list statements have been altered. Because of this, the technician believes that the router is being configured by an unknown person through Telnet. Before changing the router passwords, the technician would like to discover if anyone is connected to the router by Telnet and stop them from making further changes.Which commands will accomplish these options?()
Which connections allow the use of full-duplex Ethernet?()
How many usable sub network and usable hosts per subnet result in the network address 201.105.13.0 is sub netted with a mask of /26? ()
Which of the following contribute to congestion on an Ethernet network?()
A router with a serial interface will be used for an ISDN link.What other function group devices are required to complete the connection to the service provider? ()
A technician at TestKing needs to update the network documentation. One of the tasks includes documenting the name of the IOS image file of each router in the network.Which commands could be used to find this information?()