Based on the network diagram and routing table output in the exhibit,
which of these statements is true? ()
A. InterVLAN routing will not occur since no routing protocol has been configured.
B. InterVLAN routing has been configured properly, and the workstations have connectivity to each other.
C. Although interVLAN routing is not enabled, both workstations will have connectivity to each other.
D. Although interVLAN routing is enabled, the workstations will not have connectivity to each other.
您可能感兴趣的试卷
你可能感兴趣的试题
Refer to the exhibit. VLAN2, VLAN3, and VLAN10 are configured on the switch D-SW1. Host computers are on VLAN 2 (10.1.2.0), servers are on VLAN 3 (10.1.3.0), and the management VLAN is on VLAN10 (10.1.10.0). Hosts are able to ping each other but are unable to reach the servers. On the basis of the exhibited output,
which configuration solution could rectify the problem?()
A. Assign an IP address of 10.1.3.1/24 to VLAN3.
B. Configure default gateways to IP address 10.1.10.1 on each host.
C. Enable IP routing on the switch D-SW1.
D. Configure a default route that points toward network 200.1.1.0/24.
E. Configure default gateways to IP address 10.1.2.1 on each host.
F. Configure default gateways to IP address 200.1.1.2 on each host.
Refer to the exhibit. Host A and Host B are connected to the Catalyst 3550 switch and have been assigned to their respective VLANs. The rest of the 3550 configuration is the default configuration. Host A is able to ping its default gateway, 10.10.10.1, but is unable to ping Host B. Given the output displayed in the exhibit,
which statement is true? ()
A. A separate router is required to support interVLAN routing.
B. VTP must be configured to support interVLAN routing.
C. VLANs 10 and 15 must be created in the VLAN database mode.
D. The global config command ip routing must be configured on the SW1 switch.
E. HSRP must be configured on SW1.
F. Interface VLAN 10 must be configured on the SW1 switch.
Refer to the exhibit. Dynamic ARP inspection (DAI) is enabled on switch SW_A only. Both Host_A and Host_B acquire their IP addresses from the DHCP server connected to switch SW_A.
What would the outcome be if Host_B initiated an ARP spoof attack toward Host_A ? ()
A. The spoof packets will be inspected at the ingress port of switch SW_A and will be permitted.
B. The spoof packets will not be inspected at the ingress port of switch SW_A and will be permitted.
C. The spoof packets will not be inspected at the ingress port of switch SW_A and will be dropped.
D. The spoof packets will be inspected at the ingress port of switch SW_A and will be dropped.
Refer to the exhibit.
What will happen to traffic within VLAN 14 with a source address of 172.16.10.5? ()
A. The traffic will be forwarded to the router processor for further processing.
B. The traffic will be dropped.
C. The traffic will be forwarded to the TCAM for further processing.
D. The traffic will be forwarded without further processing.
A hacker on the Company network is attempting to hop onto a different VLAN.
Which two statements about VLAN hopping are true? ()
A. An end station attempts to gain access to all VLANs by transmitting Ethernet frames in the 802.1q encapsulation.
B. Configuring an interface with the "switchport mode dynamic" command will prevent VLAN hopping.
C. Attacks are prevented by utilizing the port-security feature.
D. Configuring an interface with the "switchport mode access" command will prevent VLAN hopping.
E. An end station attempts to redirect VLAN traffic by broadcasting multiple ARP requests.
The Company security administrator wants to prevent VLAN hopping on the network.
What is one method that can be used to do this? ()
A. Attacks are prevented by utilizing the port-security feature.
B. An end station attempts to gain access to all VLANs by transmitting Ethernet frames in the 802.1q encapsulation.
C. Configuring an interface with the switchport mode dynamic command will prevent VLAN hopping.
D. An end station attempts to redirect VLAN traffic by transmitting Ethernet frames in the 802.1q encapsulation.
E. Configuring an interface with the "switchport mode access" command will prevent VLAN hopping.
The Company security administrator is concerned with VLAN hopping based attacks.
Which two statements about these attacks are true? ()
A. Attacks are prevented by utilizing the port-security feature.
B. An end station attempts to gain access to all VLANs by transmitting Ethernet frames in the 802.1q encapsulation.
C. Configuring an interface with the switchport mode dynamic command will prevent VLAN hopping.
D. An end station attempts to redirect VLAN traffic by transmitting Ethernet frames in the 802.1q encapsulation.
E. Configuring an interface with the "switchport mode access" command will prevent VLAN hopping.
Refer to the exhibit. PCs in VLAN 2 are not able to communicate with PCs in VLAN 3.
What could be the cause?()
A. IP routing is not enabled.
B. VTP is not configured correctly on the interfaces.
C. The command mls rp management-interface is missing.
D. The command mls rp ip must be disabled to enable the routing.
You are configuring a Cisco multilayer switch for the Company network.
Which command would you use to configure a port to act as a routed interface?()
A. ip routing
B. switchport mode trunk
C. no switchport
D. switchport trunk native vlan 1
E. None of the other alternatives apply
Which of the following could be used to provide a Layer 3 data path between separate VLANs?()
A. VLAN trunking
B. An external router
C. An internal route processor
D. VLAN capable bridge
E. EtherChannel
最新试题
What must be the same to make multiple switches part of the same Multiple Spanning Tree (MST)?()
Refer to the exhibit. What does the command channel-group 1 mode desirable do? ()
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result?()
If G1/0/1 on DS1 is shutdown, what will be the current priority value of the Vlan105’s group on DS1 ?()
Which two statements are true about BPDU port-guard and BPDU filtering?()
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain, the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change?()
Which two statements about the various implementations of STP are true?()
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port:00:06:34: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/5 (not half duplex), with SW_A FastEthernet0/4 (half duplex) , with TBA05071417(Cat6K-B) 0/4 (half duplex). What would be the possible outcome of the problem?()
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ? ()
Refer to the exhibit. Based on the output of the show spanning-tree command, which statement is true? ()