Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A.
What will happen as a result of this change？（）
A.All ports of the root switch SW_A will remain in forwarding mode throughout the reconvergence of the spanning tree domain.
B.Switch SW_A will change its spanning tree priority to become root for VLAN 2 only.
C.Switch SW_A will remain root for the default VLAN and will become root for VLAN 2.
D.No other switch in the network will be able to become root as long as switch SW_A is up and running.
您可能感兴趣的试卷
你可能感兴趣的试题
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1.
What will be the result？（）
A.The command will be rejected by the switch.
B.Interfaces FastEthernet0/13 and FastEthernet0/14 will no longer be bundled.
C.Dynamic Trunking Protocol will be turned off on interfaces FastEthernet0/13 and FastEthernet0/14.
D.Interfaces FastEthernet0/13 and FastEthernet0/14 will only allow traffic from the native VLAN.
E.Interfaces FastEthernet0/13 and FastEthernet0/14 will continue to pass traffic for VLANs 88，100，360.
Refer to the exhibit.
What will happen when one more user is connected to interface FastEthernet 5/1？ （）
A.All secure addresses will age out and be removed from the secure address list. This will cause the security violation counter to increment.
B.The first address learned on the port will be removed from the secure address list and be replaced with the new address.
C.The interface will be placed into the error-disabled state immediately， and an SNMP trap notification will be sent.
D.The packets with the new source addresses will be dropped until a sufficient number of secure MAC addresses are removed from the secure address list.
Refer to the exhibit. LACP has been configured on Switch1 as shown.
Which is the correct command set to configure LACP on Switch2？（）
A.Switch2# configure terminal Switch2（config）# interface range gigabitethernet3/1 -2 Switch2（config-if）# channel-group 5 mode auto
B.Switch2# configure terminal Switch2（config）# interface range gigabitethernet3/1 -2 Switch2（config-if）# channel-group 5 mode passive
C.Switch2# configure terminal Switch2（config）# interface range gigabitethernet3/1 -2 Switch2（config-if）# channel-group 5 mode desirable
D.Switch2# configure terminal Switch2（config）# interface range gigabitethernet3/1 -2 Switch2（config-if）# channel-group 5 mode on
Refer to the exhibit.
What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
A.ip routing
B.no ip routing
C.router eigrp 1
D.no router eigrp 1
E.mls qos
F.no mls qos
A.VLAN instance mapping and revision number
B.VLAN instance mapping and member list
C.VLAN instance mapping， revision number， and member list
D.VLAN instance mapping， revision number， member list， and timers
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct，
what will be true about Switch 15？（）
A.All ports will be in forwarding mode.
B.All ports in VLAN 10 will be in forwarding mode.
C.All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in blocking mode.
D.All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in standby mode.
A.BPDU port-guard can be enabled globally， whereas BPDU filtering must be enabled on a per-interface basis.
B.When globally enabled， BPDU port-guard and BPDU filtering apply only to PortFast enabled ports.
C.When globally enabled， BPDU port-guard and BPDU filtering apply only to trunking-enabled ports.
D.When a BPDU is received on a BPDU port-guard enabled port， the interface goes into the err-disabled state.
E.When a BPDU is received on a BPDU filtering enabled port， the interface goes into the err-disabled state.
F.When a BPDU is received on a BPDU filtering enabled port， the interface goes into the STP blocking state.
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：
00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）.
What would be the possible outcome of the problem？（）
A.The root port on switch SW_A will automatically transition to full-duplex mode.
B.The root port on switch SW_B will fallback to full-duplex mode.
C.The interfaces between switches SW_A and SW_B will transition to a blocking state.
D.Interface Fa 0/6 on switch SW_B will transition to a forwarding state and create a bridging loop.
A.mon Spanning Tree maintains a separate spanning-tree instance for each VLAN configured in the network.
B.The Spanning Tree Protocol （STP） is an evolution of the IEEE 802.1w standard.
C.Per-VLAN Spanning Tree （PVST） supports 802.1Q trunking.
D.Per-VLAN Spanning Tree Plus（PVST+） is an enhancement to 802.1Q specification and is supported only on Cisco devices.
E.Rapid Spanning Tree Protocol （RSTP） includes features equivalent to Cisco PortFast， UplinkFast， and BackboneFast for faster network reconvergence.
F.Multiple Spanning Tree （MST） assumes one spanning-tree instance for the entire Layer 2 network， regardless of the multiple number of VLANs
Refer to the exhibit. For what purpose is the command show ip cef used？（）
A.to display rewritten IP unicast packets
B.to display ARP resolution packets
C.to display ARP throttling
D.to display TCAM matches
E.to display CEF-based MLS lookups
F.to display entries in the Forwarding Information Base （FIB）
最新试题
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
Which three statements about STP timers are true？（）
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
What two things will occur when an edge port receives a BPDU？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）