The relevant portion of the Barrymore router configuration is displayed below:
In your effort to conserve precious bandwidth, you set up some ACL's to deny internet access to the remote server located at 192.168.20.5. A few minutes after reconfiguring (as shown in the exhibit above) you notice that some web traffic is still going through.Based on the above output, what do you suspect as to why the traffic still traveling over the ISDN link?（）
A. Broadcasts are creating "interesting" traffic.
B. The access-list is not configured correctly.
C. The command ip access-group 129 out is missing from the bri0/0 interface.
D. The dialer-group has not been applied to outbound traffic.
您可能感兴趣的试卷
你可能感兴趣的试题
A. show interface list
B. show ip route
C. show ip interface
D. show ip interface brief
E. show interface
On a newly installed router, the following access list is added to the HSSI interface for incoming traffic:Access-list 101 permit tcp any 10.18.10.0 0.0.0.255 eq tcp
What is the effect of the "any" keyword in the above access list?（）
A. check any of the bits in the source address
B. permit any wildcard mask for the address
C. accept any source address
D. check any bit in the destination address
E. permit 255.255.255.255 0.0.0.0
F. accept any destination
On your newly installed router, you apply the access list illustrated below to interface Ethernet 0 on a Cisco router. The interface is connected to the 192.168.1.8/29 LAN.
access-list 123 deny tcp 192.168.166.18 0.0.0.7 eq 20 any
access-list 123 deny tcp 192.168.166.18 0.0.0.7 eq 21 any
How will the above access lists affect traffic?（）
A. All traffic will be allowed to exit E0 except FTP traffic.
B. FTP traffic from 192.168.166.19 to any host will be denied.
C. FTP traffic from 192.168.166.22 to any host will be denied.
D. All traffic exiting E0 will be denied.
E. All FTP traffic to network 192.168.166.18/29 from any host will be denied.
A. TestKingB> telnet
B. TestKingB > ping
C. TestKingB > trace
D. TestKingB > show ip route
E. TestKingB > show interface
F. TestKingB > show cdp neighbors
A. ping
B. trace
C. show ip route
D. show interface
E. show cdp neighbors
A. Serial 0 is up, line protocol is up
B. Serial 0 is up, line protocol is down
C. Serial 0 is down, line protocol is down
D. Serial 0 is down, line protocol is up
E. Serial 0 is administratively down, line protocol is down
F. Serial 0 is administratively down, line protocol is up
There is a connectivity problem between the serial 0/0 interface of router TESTKING1 and the serial 0/0 interface of TESTKING2. A leased line point to point circuit is installed between these two routers. The output from the "show interface serial 0/0" command is displayed below for each of these routers:
From your observations of the above exhibit, what is the underlying cause of the problem?（）
A. The loopback is not set.
B. The serial cable is faulty.
C. The subnet mask is not configured properly.
D. The IP address is not configured properly.
E. The Layer 2 frame types are not compatible.
F. The keepalive setting is not configured properly.
The relevant configuration files for the TestKing1 and TestKing2 routers are displayed below:
With due consideration to the command outputs, which of the following reasons would you attribute the connectivity problem between the two routers?（）
A. The authentication needs to be changed to PAP for both routers.
B. The serial IP addresses of routers are not on the same subnet.
C. The username/password combination is incorrectly configured.
D. The router names are incorrectly configured.
A. ICMP echo request
B. Information interrupt request
C. Timestamp reply
D. Source quench
E. None of the above
The Testking router is running RIP as the routing protocol, and the IP routing table is displayed below:
Gateway of last resort is 10.1.2.2 to network 0.0.0.0
10.0.0.0/24 is subnetted, 2 subnets
R 10.1.3.0 [120/1] via 10.1.2.2, 00:00:00, Serial0/0
C 10.1.2.0 is directly connected, Serial0/0
C 10.1.5.0 is directly connected, Serial0/1
C 10.1.6.0 is directly connected, FastEthernet0/0
R* 0.0.0.0/0 [120/1] via 10.1.5.5, 00:00:00, Serial0/1
Based on the output above, if an administrator pings host 10.1.8.5 from host
10.1.6.100, how will the router TestkingA process the ICMP packets?（）
A. The packets will be discarded.
B. The packets will be routed out the S0/0 interface.
C. The packets will be routed out the S0/1 interface.
D. The packets will be routed out the Fa0/0 interface.
E. The packets will be routed through the 10.1.2.2 gateway.
最新试题
Which Frame Relay feature is responsible for transmitting keepalives to ensure that the PVC does not shut down because of inactivity?（）
What feature of a networks switch allows an administrative to create separate broadcast domains?（）
Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? （）
The following access list was applied outbound on he E0 interface connected to the 192.168.1.8/29 LAN:access-list 123 deny tcp 192.168.1.8 0.0.0.7 eq 20 anyaccess-list 123 deny tcp 192.168.1.9 0.0.0.7 eq 21 anyWhat effect will this access list have?（）
A router with a serial interface will be used for an ISDN link.What other function group devices are required to complete the connection to the service provider? （）
Which of the following correctly describe steps in the OSI data encapsulation process?（）
What is the subnetwork address for a host with IP address 201.100.5.68/28?（）
A technician at TestKing needs to update the network documentation. One of the tasks includes documenting the name of the IOS image file of each router in the network.Which commands could be used to find this information?（）
A Router with a BRI/T interface will be used for an ISDN Connection what other ISDN device is required to complete this connection? （）
A network host is configured as follows: Host IP address: 192.168.16.183 Subnet mask: 255.255.255.224 Default gateway: 192.168.16.190 Which of the following statements describe the network to which this host is attached?（）