Routers can send hello messages in three HSRP states.
Which ones are they?()
A. Standby
B. Learn
C. Listen
D. Speak
E. Active
您可能感兴趣的试卷
你可能感兴趣的试题
Router R1 is configured for HSRP.
Which of the following are valid HSRP states on R1? ()
A. Init
B. Idle
C. Active
D. Standby
E. Established
F. Backup
You have configured router R1 with HSRP, using the standard defaults.
Which three statements are true of a default HSRP configuration?()
A. The Standby hello time is 2 seconds.
B. Two HSRP groups are configured.
C. The Standby track interface priority is 10.
D. The Standby hold time is 10 seconds
E. The Standby priority is 100.
F. The Standby delay is 3 seconds.
You need to design router redundancy on the Company network.
Which three protocols could be chosen for IP routing redundancy to protect against first-hop router failure?()
A. GLBP
B. ICMP
C. MSTP
D. HSRP
E. VRRP
F. NHRP
Router R1 and R2 are both configured for HSRP.
Which two statements about the HSRP priorities of these two routers are true?()
A. To assign the HSRP router priority in a standby group, the standby group-number priority priority-value global configuration command must be used.
B. The default priority of a router is zero (0).
C. The no standby priority command assigns a priority of 100 to the router.
D. Assuming that preempting has also been configured, the router with the lowest priority in an HSRP group would become the active router.
E. When two routers in an HSRP standby group are configured with identical priorities, the router with the highest configured IP address will become the active router.
Which first-hop redundancy solution listed would supply Company clients with MAC address0000.0C07.AC0A for group 10 in response to an ARP request for a default gateway?()
A. IRDP
B. Proxy ARP
C. GLBP
D. HSRP
E. VRRP
F. IP Redirects
You work as a network technician at Company. Your boss, Mrs. , is interested in
GLBP. In particular, she wants to know the multicast address that this protocol uses.
What should you tell her? ()
A. 224.0.0.100
B. 224.0.0.1
C. 224.0.0.102
D. 224.0.0.10
E. 224.0.0.101
F. None of the other alternatives apply
A. IRDP
B. SNMP
C. HSRP
D. VRRP
A. Proxy ARP
B. HSRP
C. IRDP
D. VRRP
E. GLBP
In the hardware address 0000.0c07.ac0av,
what does 07.ac represent? ()
A. HSRP well-known physical MAC address
B. Vendor code
C. HSRP router number
D. HSRP group number
E. HSRP well-known virtual MAC address
A. per host using a round robin scheme
B. per host using a strict priority scheme
C. per session using a round robin scheme
D. per session using a strict priority scheme
E. per GLBP group using a round robin scheme
F. per GLBP group using a strict priority scheme
最新试题
Refer to the exhibit. For what purpose is the command show ip cef used?()
Which two statements are true about BPDU port-guard and BPDU filtering?()
Which two statements are true when the extended system ID feature is enabled? ()
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port:00:06:34: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/5 (not half duplex), with SW_A FastEthernet0/4 (half duplex) , with TBA05071417(Cat6K-B) 0/4 (half duplex). What would be the possible outcome of the problem?()
How are STP timers and state transitions affected when a topology change occurs in an STP environment?()
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method?()
Refer to the exhibit. Based on the output of the show spanning-tree command, which statement is true? ()
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2?()
Which two statements about the various implementations of STP are true?()
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1? ()