Refer to the exhibit.
Which of the following should you do to configure the IP phone to override the priority of the data packets it receives from the host? ()
A. Issue the mls qos trust cos command on the switch port connected to the IP phone.
B. Issue the switchport priority extend cos command on the switch port connected to the IP phone.
C. Issue the switchport priority extend cos command on the IP phone.
D. Issue the mls qos trust cos command on the IP phone.
您可能感兴趣的试卷
你可能感兴趣的试题
You administer a network that uses two routers, R1 and R2, configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows:
R1#configure terminal
R1(config)#interface fa0/0
R1(config-if)#ip address 10.10.0.5 255.255.255.0
R1(config-if)#standby 1 priority 150
R1(config-if)#standby preempt delay minimum 50
R1(config-if)#standby 1 track interface fa0/2 15
R1(config-if)#standby 1 ip 10.10.0.20
Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1?()
A. The HSRP priority for router R1 will increase to 200.
B. Router R1 will become the standby router if the priority drops below 50.
C. The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down.
D. Router R1 will wait 50 seconds before attempting to preempt the active router.
Routers R1 and R2 are configured for HSRP as shown below:
Router R1:
interface ethernet 0
ip address 20.6.2.1 255.255.255.0
standby 35 ip 20.6.2.21
standby 35 priority 100
interface ethernet 1
ip address 20.6.1.1.2 255.255.255.0
standby 34 ip 20.6.1.21
Router R2:
interface ethernet 0
ip address 20.6.2.2 255.255.255.0
standby 35 ip 20.6.2.21
interface ethernet 1
ip address 20.6.1.1.1 255.255.255.0
standby 34 ip 20.6.1.21
standby 34 priority 100
You have configured the routers R1 & R2 with HSRP. While debugging router R2 you notice very
frequent HSRP group state transitions.
What is the most likely cause of this? ()
A. physical layer issues
B. no spanning tree loops
C. use of non-default HSRP timers
D. failure to set the command standby 35 preempt
Exhibit
Which command will ensure that Company2 will be the primary router for traffic using the gateway address of 172.16.15.20? ()
A. On R2 add the command standby 1 priority 80
B. On R1 add the command standby 1 priority 110
C. On R1 add the command standby 1 priority 80
D. On R2 remove the command standby 1 preempt
Refer to the exhibit. What statement is true based upon the configuration of router R1 and router R2?()
A. Router R2 will become the master for Virtual Router 1, and router R1 will become the backup for Virtual Router 2.
B. Router R1 will become the master for Virtual Router 1, and router R2 will become the backup for Virtual Router 2.
C. Router R1 will become the active virtual gateway.
D. Router R2 will become the active virtual gateway.
E. The hello and hold timers are incompatible with OSPF type 5 LSAs.
F. The hello and hold timers are incompatible with multi-homed BGP.
.Refer to the exhibit and the partial configuration on routers R1 and R2. Hot Standby Routing Protocol (HSRP) is configured on the network to provide network redundancy for the IP traffic. The network administrator noticed that R2 does not become active when the R1 serial0 interface goes down.
What should be changed in the configuration to fix the problem? ()
A. The Serial0 interface on router R2 should be configured with a decrement value of 20.
B. The Serial0 interface on router R1 should be configured with a decrement value of 20.
C. R2 should be configured with a standby priority of 100.
D. R2 should be configured with a HSRP virtual address.
Refer to the exhibit. Based on the debug standby output in the exhibit, which HSRP statement is true? ()
A. DSW111 is the active router because it is the only HRSP-enabled router on that segment.
B. DSW111 is the active router because the standby timer has been incorrectly configured.
C. DSW111 is the active router because it has a lower priority on that VLAN.
D. DSW111 is the active router because it has a lower IP address than the tying priority router on that VLAN.
E. DSW111 is the active router and is advertising the virtual IP address 10.10.10.111 on VLAN 11.
Refer to the exhibit. Based on the debug standby output in the exhibit,
which HSRP statement is true?()
A. DSW111 is the active router because it is the only HRSP-enabled router on that segment.
B. DSW111 is the active router because the standby timer has been incorrectly configured.
C. DSW111 is the active router because it has a lower priority on that VLAN.
D. DSW111 is the active router because it has a lower IP address than the tying priority router on that VLAN.
E. DSW111 is the active router and is advertising the virtual IP address 10.10.10.111 on VLAN 11.
Refer to the exhibit. Assume that Host A can ping the corporate headquarters and that HSRP is configured on DSw1, which is then reloaded. Assume that DSw2 is then configured and reloaded. On the basis of this information,
what conclusion can be drawn? ()
A. DSw1 will be the active router because it has the lower priority configured.
B. DSw1 will be the standby router because it has the lower IP address.
C. DSw2 will be the active router because it booted last.
D. DSw1 will be the active router because it booted first.
E. DSw2 will be the active router because it has the higher priority that is configured.
F. DSw2 will be the standby router because it has the higher IP address.
A. Spanning Tree Protocol (STP)
B. Delay reduction
C. Hot Standby Routing Protocol (HSRP)
D. Dynamic routing protocols
E. Quality of Service (QoS)
F. Jitter management
What can be determined about the HSRP relationship from the displayed debug output? ()
A. Router 172.16.11.112 will be the active router because its HSRP priority is preferred over router 172.16.11.111.
B. Router 172.16.11.111 will be the active router because its HSRP priority is preferred over router 172.16.11.112.
C. The IP address 172.16.11.111 is the virtual HSRP router IP address.
D. The IP address 172.16.11.112 is the virtual HSRP router IP address.
E. The nonpreempt feature is enabled on the 172.16.11.112 router.
F. The preempt feature is not enabled on the 172.16.11.111 router.
最新试题
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port:00:06:34: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/5 (not half duplex), with SW_A FastEthernet0/4 (half duplex) , with TBA05071417(Cat6K-B) 0/4 (half duplex). What would be the possible outcome of the problem?()
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this?()
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain, the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change?()
During routine maintenance, G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However, after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ? ()
Refer to the exhibit. Based on the output of the show spanning-tree command, which statement is true? ()
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method?()
What two things will occur when an edge port receives a BPDU?()
If G1/0/1 on DS1 is shutdown, what will be the current priority value of the Vlan105’s group on DS1 ?()
Refer to the exhibit. What does the command channel-group 1 mode desirable do? ()
Which statement is correct about RSTP port roles?()