When configuring a cisco 3845 integrated services router to support 802.11b and g clients.
Which of the following commands would be correct?()
A.router(config-if)# speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
B.router(config-if)# speed 1.0 2.0 5.5 6.0 9.0 basic-11.0 12.0 basic-18.0 24.0 36.0 48.0 54.0
C.router(config-if)# speed basic-1.0 2.0 5.5 basic-6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
D.router(config-if)# speed 1.0 2.0 5.5 basic-6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
您可能感兴趣的试卷
你可能感兴趣的试题
A.enable concatenation on the non-root bridge only
B.enable concatenation on the root bridge only
C.enable concatenation on both the root bridge and non-root bridge
D.enable concatenation on the root bridge and set it as desirable on the non-root bridge
E.set concatenation as desirable on the root bridge and enable it on the non-root bridge
Eap-fast provides a secure tunnel during phase one to protect the user’s authentication credentials.
Which of these entities initializes the secure tunnel?()
A.x.509 certificate
B.generic token card
C.pre shared key
D.protected access credential
Your customer has deployed a cisco wireless location appliance within its warehouse
environment. however,employees there have been experiencing problems when tracking objects using active rfid tags. the rfid beacon rate is 10 seconds and you have discovered an issue with the rfid timeout value.
Where and how should the rfid value be changed?()
A.on the cisco wcs, to 95 seconds
B.on the wireless controller, to 45 seconds
C.on the wireless controller, to 95 seconds
D.on the cisco wcs, to 45 seconds
You are installing a cisco aironet 1000 series controller-based access point. when you boot it, all the leds on the access point blink together.
What does this indicate about the access point?()
A.duplicate ip address
B.code upgrade in progress
C.normal operation
D.searching for primary controller
A.ipx
B.ip
C.udp
D.tcp
A.14
B.15
C.17
D.16
A.location appliance
B.controller-based access points
C.wireless clients
D.wireless control system
E.wireless controllers
A.48
B.36
C.12
D.24
A.10
B.5
C.15
D.20
A.project planning
B.configuration management
C.wireless readiness assessment
D.systems acceptance testing
E.site readiness specification
最新试题
On a WLAN controller, what is the default roaming bandwidth percentage reserved for voice clients?()
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it, allthe LEDs on the access point blink together.What does this indicate about the access point?()
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port?()
You review the Failed Attempts logs on an AAA server and find: "unknown network access servererror." Which failure could produce this error?()
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is, you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to?()
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones,which two general control settings should you select?()
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor,4GB RAM, and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem?()
If it is properly deployed, a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller?()
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add?()
On a Cisco Aironet 1240AG Series standalone access point, the radio LED is dark blue and blinking,but the status LED and Ethernet LED are both off.What does this indicate?()