You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it, allthe LEDs on the access point blink together.
What does this indicate about the access point?()
A.normal operation
B.duplicate IP address
C.code upgrade in progress
D.searching for primary controller
您可能感兴趣的试卷
你可能感兴趣的试题
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.
What is the maximum number of WLAN controllers that you can add?()
A.12
B.17
C.20
D.24
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.
Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective?()
A.Transmit Mobile Anchor Export message
B.Receive Mobile Anchor Export message
C.Transmit Plumbing duplex mobility tunnel message
D.Receive Plumbing duplex mobility tunnel message
A.4
B.8
C.16
D.32
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.
Before you press and hold the MODEbutton, you should verify that the file name is which of the following?()
A.c1130-k9w7-tar.boot
B.c1130-k9w7-tar.default
C.c1130-k9w7-tar.recover
D.c1130-k9w7-tar.123-7.JA1.tar
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but, when you answer, the call is dropped.
What may cause this problem?()
A.The minimum data rate is not set to 11 Mbps.
B.An address resolution protocol is enabled.
C.Publicly Secure Packet forwarding is enabled.
D.The access point is set to the least congested channel.
A.45
B.60
C.15
D.30
A.client traffic allowed, data captured on all channels
B.client traffic allowed, data captured on a single channel
C.no client traffic allowed, data captured on a single channel
D.no client traffic allowed, data captured on all channels
You are installing a Cisco 4402 Series Wireless LAN Controller.
What type of interface is used on the uplink port?()
A.1000Base-X Mini-GBIC
B.10/100/1000 Mbps RJ45
C.10/100 Mbps RJ45
D.1000Base-SX
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.
Which of the following will cause this problem?()
A.invalid radio type selected
B.no WEP key configured on the client
C.invalid SSID configured
D.invalid WEP key
最新试题
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem?()
The Cisco Wireless Location Appliance provides an audit trail for each device tracked for up to how many days?()
You are using ADU and are authenticated and associated to an access point. However, you are unable to obtain an IP address.Which of these has caused this problem?()
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS? ()
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side,which of the following actionsshould you perform on the wired infrastructure?()
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem?()
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter,the status LED and activity LED are alternating on and off.What does this indicate?()
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but, when you answer, the call is dropped.What may cause this problem?()
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance?()
If it is properly deployed, a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller?()