A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.
Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective?()
A.Transmit Mobile Anchor Export message
B.Receive Mobile Anchor Export message
C.Transmit Plumbing duplex mobility tunnel message
D.Receive Plumbing duplex mobility tunnel message
您可能感兴趣的试卷
你可能感兴趣的试题
A.4
B.8
C.16
D.32
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.
Before you press and hold the MODEbutton, you should verify that the file name is which of the following?()
A.c1130-k9w7-tar.boot
B.c1130-k9w7-tar.default
C.c1130-k9w7-tar.recover
D.c1130-k9w7-tar.123-7.JA1.tar
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but, when you answer, the call is dropped.
What may cause this problem?()
A.The minimum data rate is not set to 11 Mbps.
B.An address resolution protocol is enabled.
C.Publicly Secure Packet forwarding is enabled.
D.The access point is set to the least congested channel.
A.45
B.60
C.15
D.30
A.client traffic allowed, data captured on all channels
B.client traffic allowed, data captured on a single channel
C.no client traffic allowed, data captured on a single channel
D.no client traffic allowed, data captured on all channels
You are installing a Cisco 4402 Series Wireless LAN Controller.
What type of interface is used on the uplink port?()
A.1000Base-X Mini-GBIC
B.10/100/1000 Mbps RJ45
C.10/100 Mbps RJ45
D.1000Base-SX
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.
Which of the following will cause this problem?()
A.invalid radio type selected
B.no WEP key configured on the client
C.invalid SSID configured
D.invalid WEP key
A.Object Definitions
B.Asset Management
C.Location Views
D.Network Connections
An REAP was supporting 16 WLANs, but now it only supports one.
What happened to cause the change?()
A.Controller connectivity has been lost.
B.The access point lost its configuration.
C.The access point was rebooted.
D.An access point firmware upgrade is in progress.
最新试题
You are trying to change the polling parameters used by the location manager via the Cisco WCS,and your request is being denied. What is wrong?()
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter,the status LED and activity LED are alternating on and off.What does this indicate?()
The Cisco Wireless Location Appliance provides an audit trail for each device tracked for up to how many days?()
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but, when you answer, the call is dropped.What may cause this problem?()
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add?()
On a Cisco Aironet 1240AG Series standalone access point, the radio LED is dark blue and blinking,but the status LED and Ethernet LED are both off.What does this indicate?()
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem?()
You are using ADU and are authenticated and associated to an access point. However, you are unable to obtain an IP address.Which of these has caused this problem?()
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem?()
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton, you should verify that the file name is which of the following?()