A. Under the Admin tab on the FI
B. Under the Server tab in the service profile
C. Under the SAN tab on each VSAN
D. Under the Admin tab on the chassis
E. Under the SAN tab on the Fabric Interconnect
您可能感兴趣的试卷
你可能感兴趣的试题
Given the following output：
san-port-channel 12 is up
Hardware is Fibre Channel
Port WWN is 24：0c：00：0d：ec：d3：5c：00
Admin port mode is NP， trunk mode is on
Port mode is NP Port vsan is 1
Speed is 8 Gbps
Member[1] ： fc2/3
Member[2] ： fc2/4
What does "Speed is 8 Gbps" indicate？（）
A. The speed of the slowest interface in the port channel
B. The combined speed of all interfaces configured in the port channel
C. The combined speed of all interfaces in the port channel that are up
D. The speed that can be achieved if all buffers are used
A. Server
B. End device
C. Node
D. Host
E. Virtual
A. Sending all broadcasts
B. Receiving all traffic from upstream switches
C. Receiving broadcast traffic
D. Negotiating spanning tree with upstream switches
E. Learning MAC addresses from upstream switches
A. The Cisco VIC can create an unlimited number of Virtual NICs
B. The number of vNICs on the Cisco VIC that can be created is determined by the number of chassis uplinks
C. vNICs are created using software on the host operating system
D. The host operating system sees a vNIC as a physical PCIe device
E. The host operating system sees a vNIC as a sub-interface of a primary NIC
F. The Cisco VIC can create 1024 vNICs
A. Fibre Channel storage
B. UCS C-Series servers
C. NFS storage
D. UCS chassis
E. Other fabric interconnect
A. End-host mode is synonymous with NPV mode.
B. In end-host mode， only hard pinning of vHBAs to Fibre Channel uplink ports is allowed.
C. Making configuration changes between Fibre Channel switching mode and end-host mode is nondisruptive.
D. End-host mode is the default Fibre Channel switching mode.
A. In the blade BIOS
B. In the operating system
C. In the service profile
D. In the card option ROM
A. The QoS policy assigns a system class to the outgoing traffic for a vNIC or vHBA.
B. Flow-control policies determine whether the uplink Ethernet ports in a Cisco UCS environment send and receive IEEE 802.3x pause frames when the send buffer for a port fills.
C. If no system class is configured as CoS 0， the Fibre Channel system class is used.
D. The user can configure QoS for these system classes： platinum， gold， silver， best effort， Fibre Channel.
E. When configuring a system class， the type of adapter in a server may limit the maximum MTU supported.
A. boot policy and BIOS policy
B. disk scrub and boot policy
C. BIOS setting scrub， boot policy， and BIOS policy
D. disk scrub and BIOS setting scrub
A. name
B. best-effort
C. burst
D. rate
E. host control
最新试题
Which are valid statements about Cisco Virtual Interface Card （VIC）？ （）
Which statements are true regarding the Cisco UCS fabric failover feature？ （）
Your company wants Server 1/eth0 （vNIC 1） configured so that it always uses Fabric Interconnect A Port Channel 1 （Po1） when it communicates with anything outside of the Cisco UCS domain. However， if vNIC 1 fails over to Fabric Interconnect B using fabric failover， then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true？ （）
From the Cisco UCS CLI， how do you verify which uplink ports a blade server is using for its network connectivity？（）
A Cisco UCS fabric interconnect in end-host mode learns MAC addresses on which port types？（）
Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager？ （）
In the event of a GSS failure in a GSS cluster， which is true？（）
What is the purpose of this command in a Cisco Application Control Engine？（） switch/Admin# show np 1 me-stats "-F0 v"
When will an "all configuration" backup be imported into the Cisco UCS Manager？（）
Refer to the exhibit.Your company requires a Cisco UCS configuration that will， at a minimum， allow the configuration in the provided exhibit. Which Cisco UCS components will meet the requirement？（）