A wireless client cannot connect to an...

单项选择题A wireless client cannot connect to an 802.11b/g BSS with a b/g wireless card. The client section of the access point does not list any active WLAN clients. What is a possible reason for this?（）

A. The incorrect channel is configured on the client.
B. The client's IP address is on the wrong subnet.
C. The client has an incorrect pre-shared key.
D. The SSID is configured incorrectly on the client.

点击查看答案

您可能感兴趣的试卷

你可能感兴趣的试题

1.单项选择题What occurs on a Frame Relay network when the CIR is exceeded?（）

A. All TCP traffic is marked discard eligible.
B. All UDP traffic is marked discard eligible and a BECN is sent.
C. All TCP traffic is marked discard eligible and a BECN is sent.
D. All traffic exceeding the CIR is marked discard eligible.

点击查看答案

2.单项选择题A network administrator must configure 200 switch ports to accept traffic from only the currently attached host devices. What would be the most efficient way to configure MAC-level security on all these ports?（）

A. Visually verify the MAC addresses and then telnet to the switches to enter the switchport-port security mac-address command.
B. Have end users e-mail their MAC addresses. Telnet to the switch to enter the switchport-port security mac-address command.
C. Use the switchport port-security MAC address sticky command on all the switch ports that have end devices connected to them.
D. Use show mac-address-table to determine the addresses that are associated with each port and then enter the commands on each switch for MAC address port-security.

点击查看答案

3.单项选择题What is the difference between a CSU/DSU and a modem?（）

A. A CSU/DSU converts analog signals from a router to a leased line; a modem converts analog signals from a router to a leased line.
B. A CSU/DSU converts analog signals from a router to a phone line; a modem converts digital signals from a router to a leased line.
C. A CSU/DSU converts digital signals from a router to a phone line; a modem converts analog signals from a router to a phone line.
D. A CSU/DSU converts digital signals from a router to a leased line; a modem converts digital signals from a router to a phone line.

点击查看答案

4.单项选择题Which command reveals the last method used to powercycle a router?（）

A. show reload
B. show boot
C. show running-config
D. show version

点击查看答案

5.单项选择题Which protocols are found in the network layer of the OSI reference model and are responsible for path determination and traffic switching?（）

A. LAN
B. routing
C. WAN
D. network

点击查看答案

6.单项选择题Data transfer is slow between the source and destination. The quality of service requested by the transport layer in the OSI reference model is not being maintained. To fix this issue, at which layer should the troubleshooting process begin?（）

A. presentation
B. session
C. transport
D. network
E. physical

点击查看答案

7.单项选择题Which layer in the OSI reference model is responsible for determining the availability of the receiving program and checking to see if enough resources exist for that communication? （）

A. transport
B. network
C. presentation
D. session
E. application

点击查看答案

8.单项选择题A company implements video conferencing over IP on their Ethernet LAN. The users notice that the network slows down, and the video either stutters or fails completely. What is the most likely reason for this?（）

A. minimum cell rate (MCR)
B. quality of service (QoS)
C. modulation
D. packet switching exchange (PSE)
E. reliable transport protocol (RTP)

点击查看答案

9.单项选择题What must be set correctly when configuring a serial interface so that higher-level protocols calculate the best route?（）

A. bandwidth
B. delay
C. load
D. reliability

点击查看答案

10.单项选择题When configuring a serial interface on a router, what is the default encapsulation?（）

A. atm-dxi
B. frame-relay
C. hdlc
D. lapb
E. ppp

点击查看答案