单项选择题A system administrator installed a new switch using a script to configure it. IP connectivity was tested using pings to SwitchB. Later attempts to access NewSwitch using Telnet from SwitchA failed. Which statement is true?()

A. Executing password recovery is required.
B. The virtual terminal lines are misconfigured.
C. Use Telnet to connect to RouterA and then to NewSwitch to correct the error.
D. Power cycle of NewSwitch will return it to a default configuration.


您可能感兴趣的试卷

你可能感兴趣的试题

1.单项选择题A host is attempting to send data to another host on a different network. What is the first action that the sending host will take?()

A. Drop the data.
B. Send the data frames to the default gateway.
C. Create an ARP request to get a MAC address for the receiving host.
D. Send a TCP SYN and wait for the SYN ACK with the IP address of the receiving host.

2.单项选择题When two hosts are trying to communicate across a network, how does the host originating the communication determine the hardware address of the host that it wants to "talk" to?()

A. RARP request
B. Show Network Address request
C. Proxy ARP request
D. ARP request
E. Show Hardware Address request

3.单项选择题Which network protocol does DNS use?()

A. FTP
B. TFTP
C. TCP
D. UDP
E. SCP

4.单项选择题Which statement describes the process of dynamically assigning IP addresses by the DHCP server?()

A. Addresses are allocated after a negotiation between the server and the host to determine the length of the agreement.
B. Addresses are permanently assigned so that the hosts uses the same address at all times.
C. Addresses are assigned for a fixed period of time, at the end of the period, a new request for an address must be made.
D. Addresses are leased to hosts, which periodically contact the DHCP server to renew the lease.

5.单项选择题On corporate network, hosts on the same VLAN can communicate with each other, but they are unable to communicate with hosts on different VLANs. What is needed to allow communication between the VLANs?()

A. a router with subinterfaces configured on the physical interface that is connected to the switch
B. a router with an IP address on the physical interface connected to the switch
C. a switch with an access link that is configured between the switches
D. a switch with a trunk link that is configured between the switches

6.单项选择题A switch is configured with all ports assigned to vlan 2 with full duplex FastEthernet to segment existing departmental traffic. What is the effect of adding switch ports to a new VLAN on the switch?()

A. More collision domains will be created.
B. IP address utilization will be more efficient.
C. More bandwidth will be required than was needed previously.
D. An additional broadcast domain will be created.

7.单项选择题Which switch would STP choose to become the root bridge in the selection process?()

A. 32768: 11-22-33-44-55-66
B. 32768: 22-33-44-55-66-77
C. 32769: 11-22-33-44-55-65
D. 32769: 22-33-44-55-66-78

9.单项选择题Where does routing occur within the DoD TCP/IP reference model?()

A. application
B. internet
C. network
D. transport

10.单项选择题How many addresses for hosts will the network 124.12.4.0/22 provide?()

A. 510
B. 1022
C. 1024
D. 2048

最新试题

When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?()

题型:单项选择题

Three access ports have been installed and configured to a small office.What term defines the wireless topology?()

题型:单项选择题

At which layer of the OSI model is RSTP used to prevent loops?()

题型:单项选择题

If all OSPF routers in a single area are configured with the same priority value,what value dose a router use for the ODPF router ID in the absence of a loopback interface?()

题型:单项选择题

Which pairing reflects a correct protocol-and-metric relationship?()

题型:单项选择题

After the show ip route command has been entered,the follwing routes are displayed.Which route will not be entered into the routing table of a neighboring router?()

题型:单项选择题

Which command displays the CHAP authentication process as it occurs between two routers?()

题型:单项选择题

A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?()Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0

题型:单项选择题

What is the result of issuing the frame-relay map ip 192.168.1.2 202 broadcast command?()

题型:单项选择题

Which command is used to display the collection of OSPF link states?()

题型:单项选择题