A. The command is used to establish a static route.
B. The default administrative distance is used.
C. The command is used to configure the default route.
D. The subnet mask for the source address is 255.255.255.0
E. The command is used to establish a stub network
您可能感兴趣的试卷
你可能感兴趣的试题
A. TestKingRouter(config)# router ospf 0
B. TestKingRouter(config)# router ospf 1
C. TestKingRouter(config)# router ospf area 0
D. TestKingRouter(config)# network 192.168.16.0 0.0.0.255 0
E. TestKingRouter(config)# network 192.168.16.0 0.0.0.255 area 0
F. TestKingRouter(config)# network 192.168.16.0 255.255.255.0 area 0
A. Point-to-point
B. Point to multipoint
C. Broadcast
D. Non-broadcast multi-access
A. All OSPF networks require the use of multiple areas
B. Multiple OSPF areas must connect to area 0
C. Single area OSPF networks must be configured in area 1
D. Areas can be assigned any number from 0 to 63535
E. Area 0 is called the backbone area
F. Each OSPF area need to be configured with a loopback interface
A. It confines network instability to a single area of network.
B. It increases the routing overhead of the network
C. It supports VLSM
D. It routes between Autonomous Systems.
E. It allows extensive control of routing updates
A. 1
B. 64
C. 1562
D. 64000
E. 1500
A. The exchange of advertisement is triggered by a change in the network.
B. All routers exchange routing tables with each other iIn a multipoint network.
C. Packets are routed based upon the shortest path to the destination.
D. Paths are chosen depending on the cost efficiency factor.
E. Every router in an OSPF area is capable of representing the entire network topology.
F. Only the designated router in an OSPF area can represent the entire network topology.
A. Distance vector protocols send the entire routing table to directly connected neighbors.
B. Distance vector protocols are responsible for sending updates to all networks listed in the routing table.
C. Link state protocols are responsible for sending the entire routing table to the whole network.
D. Link state protocols send updates regarding their own links status to all other routers on the network.
A. The IP address of the first Fast Ethernet interface.
B. The IP address of the console management interface.
C. The highest IP address among its active interfaces.
D. The lowest IP address among its active interfaces.
E. There will be no router ID until a loopback interface is configured.
A. Point-to-point
B. Broadcast multicast
C. Nonbroadcast multicast
D. Backbone area 0
E. Virtual Link
A. The RIP route
B. The static route
C. The IGRP route
D. All three will load balance.
最新试题
Five minutes after issuing the show running-config command, a technician enters the command again and notices that several access list statements have been altered. Because of this, the technician believes that the router is being configured by an unknown person through Telnet. Before changing the router passwords, the technician would like to discover if anyone is connected to the router by Telnet and stop them from making further changes.Which commands will accomplish these options?()
What is the purpose of pressing the Ctrl+Break keys during the router password recover procedure?()
What is the subnetwork address for a host with IP address 201.100.5.68/28?()
What does a configuration Register Setting of 0x2105 indicate to the Router? ()
What is a global command?()
A router with a serial interface will be used for an ISDN link.What other function group devices are required to complete the connection to the service provider? ()
Which of the following if addresses can be assigned to host devices?()
You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?()
Which of the following describe router functions?()
Which of the following correctly describe steps in the OSI data encapsulation process?()