A. ROM Monitor mode
B. SETUP mode
C. Autoflash mode
D. RXBOOT mode
E. None of the above
您可能感兴趣的试卷
你可能感兴趣的试题
A. Show history
B. Show buffers
C. Show typed commands
D. Show terminal buffer
E. Show command
A. It will recall the previous command line
B. It will move the cursor one line up
C. It will redisplay the current command line
D. It will capitalize the command line
E. None of the above
A. RAM should be erased and the router restarted.
B. Flash should be erased and the router restarted.
C. NVRAM should be erased and the router restarted.
D. The new configuration should be entered and saved.
A. A command that can be entered in any configuration mode.
B. A command that supports all protocols.
C. A command that is implemented in all IOS versions.
D. A command that is set once and affects the entire router.
E. A command that is available in every release of IOS.
A. >
B. #
C. ?
D. *
E. All of the above
F. None of the above
A. Defines the network topology
B. Access to network resources
C. Routing and switching functions
D. Content Filtering
E. Intrusion Detection
A. show boot
B. show flash
C. show register
D. show version
E. show config
You are the administrator of the Testking network and you have forgotten the password to one of your routers. After completing the password recovery procedure the router returned to its normal operation. The config-register was set back to the initial default value.
What is this value?（）
A. 0x2112
B. 0x2104
C. 0x2102
D. 0x2142
E. 0x2100
A new switch is installed in the Testking network. This switch is to be configured sothat VLAN information will be automatically distributed to all the other Cisco Catalyst switches in the network.
Which of the conditions below have to be met in order for this to occur?（）
A. The switch that will share the VLAN information must be in the VTP Server mode.
B. The switches must be in the same VTP domain.
C. The switch that will share the VLAN information must be configured as the root bridge.
D. The switches must be configured to use the same VTP version.
E. The switches must be configured to use the same STP version.
F. The switches must be configured to use the same type of ID tagging.
G. The switches must be connected over VLAN trunks.
A. 802.1q forwarding
B. VTP transparent mode
C. Cut-through
D. Store-and-forward
E. Fragment-free
F. Frame-filtering
最新试题
Five minutes after issuing the show running-config command, a technician enters the command again and notices that several access list statements have been altered. Because of this, the technician believes that the router is being configured by an unknown person through Telnet. Before changing the router passwords, the technician would like to discover if anyone is connected to the router by Telnet and stop them from making further changes.Which commands will accomplish these options?（）
The network 172.12.0.0 needs to be divided into subnets where each subnet has the capacity of 458 IP addresses.What would be the correct subnet mask to accomplish this division keeping the number of subnets at the maximum? （）
Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? （）
Which of the following statements regarding routed and routing protocols are true?（）
Which of the following options lists the steps in PPP session establishment in the correct order?（）
New switches have been purchased for a network upgrade. The objective for the network design emphasizes efficient, error-free transport instead of fast transport.Which switching mode should be configured on the new switches to provide error-free transport to the network? （）
What is the purpose of pressing the Ctrl+Break keys during the router password recover procedure?（）
Which characteristics are representative of a link-state routing protocol?（）
What feature of a networks switch allows an administrative to create separate broadcast domains?（）
Which of the following if addresses can be assigned to host devices?（）