Which command will need to be added to External_A to ensure that it will take over if serial 0/0 on External_B fails?()
A. standby 1 priority 130
B. standby 1 preempt
C. standby 1 track fastethernet 0/0
D. standby 1 track 10.10.10.1
您可能感兴趣的试卷
你可能感兴趣的试题
Routers can send hello messages in three HSRP states.
Which ones are they?()
A. Standby
B. Learn
C. Listen
D. Speak
E. Active
Router R1 is configured for HSRP.
Which of the following are valid HSRP states on R1? ()
A. Init
B. Idle
C. Active
D. Standby
E. Established
F. Backup
You have configured router R1 with HSRP, using the standard defaults.
Which three statements are true of a default HSRP configuration?()
A. The Standby hello time is 2 seconds.
B. Two HSRP groups are configured.
C. The Standby track interface priority is 10.
D. The Standby hold time is 10 seconds
E. The Standby priority is 100.
F. The Standby delay is 3 seconds.
You need to design router redundancy on the Company network.
Which three protocols could be chosen for IP routing redundancy to protect against first-hop router failure?()
A. GLBP
B. ICMP
C. MSTP
D. HSRP
E. VRRP
F. NHRP
Router R1 and R2 are both configured for HSRP.
Which two statements about the HSRP priorities of these two routers are true?()
A. To assign the HSRP router priority in a standby group, the standby group-number priority priority-value global configuration command must be used.
B. The default priority of a router is zero (0).
C. The no standby priority command assigns a priority of 100 to the router.
D. Assuming that preempting has also been configured, the router with the lowest priority in an HSRP group would become the active router.
E. When two routers in an HSRP standby group are configured with identical priorities, the router with the highest configured IP address will become the active router.
Which first-hop redundancy solution listed would supply Company clients with MAC address0000.0C07.AC0A for group 10 in response to an ARP request for a default gateway?()
A. IRDP
B. Proxy ARP
C. GLBP
D. HSRP
E. VRRP
F. IP Redirects
You work as a network technician at Company. Your boss, Mrs. , is interested in
GLBP. In particular, she wants to know the multicast address that this protocol uses.
What should you tell her? ()
A. 224.0.0.100
B. 224.0.0.1
C. 224.0.0.102
D. 224.0.0.10
E. 224.0.0.101
F. None of the other alternatives apply
A. IRDP
B. SNMP
C. HSRP
D. VRRP
A. Proxy ARP
B. HSRP
C. IRDP
D. VRRP
E. GLBP
In the hardware address 0000.0c07.ac0av,
what does 07.ac represent? ()
A. HSRP well-known physical MAC address
B. Vendor code
C. HSRP router number
D. HSRP group number
E. HSRP well-known virtual MAC address
最新试题
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result?()
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2?()
Based on the show spanning-tree vlan 200 output shown in the exhibit, which two statements about the STP process for VLAN 200 are true? ()
Which statement is correct about RSTP port roles?()
What is the configured priority value of the Vlan105’s group on DS2 ?()
Refer to the exhibit. Based on the output of the show spanning-tree command, which statement is true? ()
During routine maintenance, it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time, DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ? ()
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2?()
Refer to the exhibit. Which statement is true about the output?()
Which two statements are true about BPDU port-guard and BPDU filtering?()