A. VTP
B. ISL
C. CDP
D. 802.1Q
E. 802.1p
F. LLC
您可能感兴趣的试卷
你可能感兴趣的试题
A. All switch and bridge ports are in the forwarding state.
B. All switch and bridge ports are assigned as either root or designated ports.
C. All switch and bridge ports are in either the forwarding or blocking state.
D. All switch and bridge ports are either blocking or looping.
A. to make VTP easier to implement
B. to isolate broadcast traffic
C. to increase the size of the collision domain
D. to allow more devices to connect to the network
E. to logically group hosts according to function
F. to increase network security
A. Install anti-virus software on the student computers.
B. Put the faculty computers in a separate VLAN.
C. Power down the switches that connect to faculty computers when they are not in use.
D. Remove the student computers from the network and put them on a peer-to-peer network.
E. Create an access list that blocks the students from the Internet where the hacking tolls are located.
A. VTP allows routing between VLANs.
B. VTP allows a single switch port to carry information to more than one VLAN.
C. VTP allows physically redundant links while preventing switching loops.
D. VTP simplifies switch administration by allowing switches to automatically share VLAN configuration information.
E. VTP helps to limit configuration errors by keeping VLAN naming consistent across the VTP domain.
F. VTP enhances security by preventing unauthorized hosts from connecting to the VTP domain.
A. TestKing1(config-if)# switchport port-security maximum 1
B. TestKing1(config)# mac-address-table secure
C. TestKing1(config)# access-list 10 permit ip host
D. TestKing1(config-if)# switchport port-security violation shutdown
E. TestKing1(config-if)# ip access-group 10
A.NCP
B.ISDN
C.SLIP
D.LCP
E.DLCI
A. ARP
B. CDP
C. DHCP
D. DNS
E. ICMP
A. to prevent routing loops
B. to create a default route
C. to provide multiple gateways for hosts
D. to maintain a loop-free Layer 2 network topology
E. to enhance the functions of SNMP
A. defines how the media is accessed
B. supplies a token to determine which host has access to the media
C. defines the encoding of electrical signals on the wire
D. determines the preamble bits
A. path cost
B. lowest port MAC address
C. VTP revision number
D. highest port priority number
E. port priority number and MAC address
最新试题
Which of the following contribute to congestion on an Ethernet network?()
Which characteristics are representative of a link-state routing protocol?()
A Router with a BRI/T interface will be used for an ISDN Connection what other ISDN device is required to complete this connection? ()
Given a subnet mask of 255.255.255.224, which of the following addresses can be assigned to network hosts?()
New switches have been purchased for a network upgrade. The objective for the network design emphasizes efficient, error-free transport instead of fast transport.Which switching mode should be configured on the new switches to provide error-free transport to the network? ()
Which of the following statements regarding routed and routing protocols are true?()
A technician at TestKing needs to update the network documentation. One of the tasks includes documenting the name of the IOS image file of each router in the network.Which commands could be used to find this information?()
The following access list was applied outbound on he E0 interface connected to the 192.168.1.8/29 LAN:access-list 123 deny tcp 192.168.1.8 0.0.0.7 eq 20 anyaccess-list 123 deny tcp 192.168.1.9 0.0.0.7 eq 21 anyWhat effect will this access list have?()
A Class C network address has been subnetted with a /27 mask.Which of the following addresses is a broadcast address for one of the resulting subnets?()
Five minutes after issuing the show running-config command, a technician enters the command again and notices that several access list statements have been altered. Because of this, the technician believes that the router is being configured by an unknown person through Telnet. Before changing the router passwords, the technician would like to discover if anyone is connected to the router by Telnet and stop them from making further changes.Which commands will accomplish these options?()