You are configuring a wireless LAN controller for QoS.
Which 802.11e user priority tag should you apply to voice applications？（）
A.1
B.3
C.4
D.6
您可能感兴趣的试卷
你可能感兴趣的试题
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.
What has causedthis problem？（）
A.H-REAP AP1 lost its connection to the controller.
B.H-REAP AP2 lost its connection to the controller.
C.H-REAP AP1 has reached its client limit.
D.H-REAP AP2 has reached its client limit.
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.
Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
A.064 Tunnel-Type
B.066 Tunnel-Client-Endpoint
C.067 Tunnel-Server-Endpoint
D.081 Tunnel-Private-Group-ID
E.082 Tunnel-Assignment-ID
F.083 Tunnel-Preference
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.
What level do you set the bandwidth to？（）
A.5 percent
B.15 percent
C.25 percent
D.35 percent
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.
In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
A.Take no action， you have achieved your goal.
B.Implement a Cisco Secure IPS sensor.
C.Implement a protected port on the access switches.
D.Implement 802.1X on the switch ports.
A.Aggressive Load Balancing on
B.Aggressive Load Balancing off
C.Multicast on
D.Multicast off
E.AP Fallback on
F.AP Fallback off
A.MS-CHAP v2
B.PAP
C.GTC
D.MD5
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.
What can be done to correct the problem？（）
A.Add 4GB RAM to the Cisco WCS.
B.Add a 120 GB hard drive to the Cisco WCS.
C.Add a new location appliance.
D.Add a new Cisco WCS server dedicated to the location appliance.
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network， but clients using PEAP are failing to log on.
Which situation would result in thistype of problem？（）
A.The AAA server is set to accept both MS-CHAP v2 and GTC for PEAP authentication.
B.Clients have been set to validate the server identity.
C.Posture validation has not been enabled.
D.Clients and server are not using certificates.
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.
What may cause this problem？（）
A.The minimum data rate is not set to 11 Mbps.
B.An address resolution protocol has been disabled
C.Publicly Secure Packet forwarding is enabled
D.The access point is set to the least congested channel.
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue and blinking，but the status LED and Ethernet LED are both off.
What does this indicate？（）
A.A firmware upgrade is in progress.
B.An access point buffer overflow is occurring.
C.The internal radio has failed.
D.The access point is booting.
最新试题
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
You are using ADU and are authenticated and associated to an access point. However， you are unable to obtain an IP address.Which of these has caused this problem？（）
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem？（）
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）
How many WLANs can a Cisco Aironet 1242 in H-REAP mode support when actively connected toa wireless controller？（）
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter，the status LED and activity LED are alternating on and off.What does this indicate？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）