A.Wireless Control System
B.Wireless clients
C.Wireless controllers
D.Control-based access points
E.Location Appliance
您可能感兴趣的试卷
你可能感兴趣的试题
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter，the status LED and activity LED are alternating on and off.
What does this indicate？（）
A.The client card has failed.
B.The client card is not associated to the network.
C.The driver has been installed incorrectly.
D.The client card has awakened from power-save mode.
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.
What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）
A.25 percent
B.40 percent
C.55 percent
D.75 percent
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.
What does this indicate about the access point？（）
A.normal operation
B.duplicate IP address
C.code upgrade in progress
D.searching for primary controller
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.
What is the maximum number of WLAN controllers that you can add？（）
A.12
B.17
C.20
D.24
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.
Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
A.Transmit Mobile Anchor Export message
B.Receive Mobile Anchor Export message
C.Transmit Plumbing duplex mobility tunnel message
D.Receive Plumbing duplex mobility tunnel message
A.4
B.8
C.16
D.32
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.
Before you press and hold the MODEbutton， you should verify that the file name is which of the following？（）
A.c1130-k9w7-tar.boot
B.c1130-k9w7-tar.default
C.c1130-k9w7-tar.recover
D.c1130-k9w7-tar.123-7.JA1.tar
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.
What may cause this problem？（）
A.The minimum data rate is not set to 11 Mbps.
B.An address resolution protocol is enabled.
C.Publicly Secure Packet forwarding is enabled.
D.The access point is set to the least congested channel.
A.45
B.60
C.15
D.30
最新试题
You review the Failed Attempts logs on an AAA server and find： "unknown network access servererror." Which failure could produce this error？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）
Which protocol does the RADIUS server use inside the secure tunnel of EAP-FAST to authenticatethe client when one-time passwords are in use？（）
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem？（）
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage？（）