A. The ONS 15216 OADM can be provisioned to add/drop one, two, or four channels via Cisco Transport Manager (CTM).
B. The ONS 15216 OADM consists only of a four-channel module, and the number of ports utilized determines whether it is a one, two, or four channel OADM.
C. Three separate OADM modules are available for one, two, and four channels. The wavelengths to be dropped and added are programmable via Cisco Transport Manager (CTM).
D. The ONS 15216 OADM consists only of a single-channel module. Two-channel and four-channel support is available by stacking the single-channel module.
E. The ONS 15216 OADM is available in one, two, four channels. There are 32 single-channel OADM modules, 16 two-channel OADM modules, and 8 four-channel OADM modules.
您可能感兴趣的试卷
你可能感兴趣的试题
Click the Exhibit button. The exhibit shows a 15454/15216 DWDM system and alarm indications. What are two possible sources of trouble shown in the system?() (Choose two.)
A. fiber failure between Sites A and d
B. EDFA failure at Site A (clockwise direction)
C. EDFA failure at Site C (clockwise direction)
D. 15216 multiplexer at Site A (counter-clockwise direction)
E. OADM pass-through (West "OUT") failure at site D (clockwise)
F. wavelengths 1 and 3 transmitter failures at Site A (clockwise direction)
A. dispersion
B. Optical SNR
C. span attenuation
D. four wave mixing
E. receiver sensitivity
A. the K1 SONET byte; the K2 SONET byte
B. the K2 SONET byte;the K1 SONET byte
C. transmitter switching;receiver detection
D. Line Overhead bytes;Path Overhead bytes
E. Path Overhead bytes;Line Overhead bytes
A. SDH circuit over a SONET network delivering it as an SDH signal
B. SDH circuit over a SONET network delivering it as a SONET signal
C. SONET circuit over an SDH network delivering it as an SDH signal
D. SONET circuit over an SDH network delivering it as a SONET signal
A. trunking
B. squelching
C. nodal bypass
D. bridge and roll
E. node failure insertion
A. Traffic is switched from the first node receiving the AIS indication.
B. Traffic is switched from the far side of the failure, allowing handshaking to occur.
C. UPSR traffic is switched from the terminating node, BLSR traffic is rerouted from the originating node in the ring.
D. UPSR traffic is switched from the terminating node, circuit by circuit. BLSR traffic is rerouted from the last reachable node in the ring.
A. Each fiber has half of its SONET capacity reserved for protection.
B. Two fibers in the span carry working traffic, while the other two fibers in the span are reserved for protection.
C. The signal is sent simultaneously in both directions around the ring. The receiver determines which fiber to listen to based on signal quality.
D. The signal is sent simultaneously in both directions around the ring. The transmitter determines which fiber has the working bit set for the receiver to acknowledge.
A. DS-1; E1
B. DS-1; STM-1
C. OC-3; STM-1
D. STS-1; STM-1
E. OC-192; STM-192
A.AMI
B.ESF
C.DUS
D.SSM
E.B3ZS
F.B8ZS
A.DUS
B.line timing
C.loop timing
D.internal timing
E.through timing
最新试题
On an ONS 15454 node you can tunnel an ().
Which three technologies are used to reduce chromatic dispersion accumulation in fiber-optic transmission systems? ()(Choose three.)
A 2.5 Gb/s (OC-48 or STM-16) optical signal with a dispersion tolerance of 1200 ps/nm goes through fiber with 18ps/nm*km of dispersion. How many 15216-DCU-350 equivalents are needed for enough compensation after traveling 100 km?()
Which timing mode is appropriate for a SONET NE that is adjacent to a SONET NE using BITS-1 timing source?()
If node 2 is accepting line timing from node 1, node 2 will send ()to node 1 as its SSM message.
What are two important considerations when using 2- or 4-channel 15216 OADMs?() (Choose two.)
For lasers with tightly controlled wavelengths, approximately how far apart are the centers of adjacent wavelengths when 100 GHz spacing is used in a DWDM system?()
A Channel ID mismatch occurs when ().
What is the difference between the transmitted power and the sensitivity of the receiver?()
SONET Code Violations (CVs) totals in the PM tables are actually an accumulation of the number of ().