A.neighbor table
B.SPF table
C.RTP table
D.topology table
E.query table
F.DUAL table
您可能感兴趣的试卷
你可能感兴趣的试题
A.1024
B.2046
C.4094
D.4096
E.8190
A.assigning a private IP address to the AP
B.changing the default SSID value
C.configuring a new administrator password
D.changing the mixed mode setting to single mode
E.configuring traffic filtering
A.The switch will not forward unicast frames.
B.The switch will forward the frame to a specific port.
C.The switch will return a copy of the frame out the source port.
D.The switch will remove the destination MAC from the switch table.
E.The switch will forward the frame to all ports except the port on which it was received.
A.can be used over analog circuits
B.maps Layer 2 to Layer 3 address
C.encapsulates several routed protocols
D.supports IP only
E.provides error correction
A.default gateway
B.DNS servers
C.FTP server
D.helper address
E.subnet mask
F.TFTP server
A.It sends data in clear text format.
B.It is no longer supported on Cisco network devices.
C.It is more secure than SSH
D.It requires an enterprise license in order to be implemented.
E.It requires that the destination device be configured to support Telnet connections.
A.Switches take less time to process frames than hubs take.
B.Switches do not forward broadcasts.
C.Hubs can filter frames.
D.Using hubs can increase the amount of bandwidth available to hosts.
E.Switches increase the number of collision domains in the network.
A.A successor route is used by EIGRP to forward traffic to a destination.
B.Successor routes are saved in the topology table to be used if the primary route fails.
C.Successor routes are flagged as "active" in the routing table.
D.A successor route may be backed up by a feasible successor route.
E.Successor routes are stored in the neighbor table following the discovery process.
A.Switch1（config-if）# switchport port-security maximum 1
B.Switch1（config）# mac-address-table secure
C.Switch1（config）# access-list 10 permit ip host
D.Switch1（config-if）# switchport port-security violation shutdown
E.Switch1（config-if）# ip access-group 10
A.It divides the network communication process into smaller and simpler components， thus aiding component development， design， and troubleshooting.
B.It enables equipment from different vendors to use the same electronic components， thus saving research and development funds.
C.It supports the evolution of multiple competing standards， and thus provides business opportunities for equipment manufacturers.
D.It encourages industry standardization by defining what functions occur at each layer of the model.
E.It provides a means by which changes in functionality in one layer require changes in other layers.
最新试题
What is the result of issuing the frame-relay map ip 192.168.1.2 202 broadcast command?（）
While troubleshooting a network problem,a technician discovers that the current copy of the Cisco IOS is outdated and needs to be updated.Which of the following commands would the technician issue to replace the Cisco router IOS with the newer version?（）
After the show ip route command has been entered,the follwing routes are displayed.Which route will not be entered into the routing table of a neighboring router?（）
On which options are standard access list based?（）
How are VTP advertisements delivered to switches across the network?（）
Which command displays the CHAP authentication process as it occurs between two routers?（）
Which address is the IPV6 all-RIP-routers muticast group address that is used by RIPng as the destaion address?（）
You have been asked to come up with a subnet mask that will allow all three web servers to be on the same network while providing the max number of subnets.Which network address and subnet mask meet this requirement?（）
Which Cisco IOS diagnostics command can disrupt the operation of a router under high-load conditions?（）
At which layer of the OSI model dose PPP perform?（）