A. Router(config)#router ospf 1
B. Router(config)#router ospf 0
C. Router(config)#router ospf area 0
D. Router(config-router)#network 192.168.16.0 0.0.0.255 area 0
E. Router(config-router)#network 192.168.16.0 0.0.0.255 0
F. Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
您可能感兴趣的试卷
你可能感兴趣的试题
A. RIP requires less time to converge
B. RIP uses less bandwidth
C. RIP is less complex to configure
D. RIP demands fewer router resources
E. RIP has a more accurate metric
A. one IP network or subnetwork for each subinterface
B. subinterface numbering that matches vlan tages
C. subinterface encapsulation identifiers that match vlan tags
D. a management domain for each subinterface
E. one physical interface for each subinterface
F. one subinterface per vlan
A. A CSU/DSU terminates a digital local loop
B. A modem terminates a digital local loop
C. A CSU/DSU terminates an analog local loop
D. A modem terminates an analog local loop
E. A router is commonly considered a DTE device
F. A router is commonly considered a DCE device
A. can be used over analog circuits
B. maps Layer 2 to Layer 3 address
C. encapsulates several routed protocols
D. supports IP only
E. provides error correction
A. Administratively shut down the interfaces.
B. Physically secure the interfaces.
C. Configure a virtual terminal password and login process.
D. Enter an access list and apply it to the terminal interfaces using the access-class command.
E. Create an access list and apply it to the terminal interfaces using the access-group command.
A.multicast
B.broadcast
C.allcast
D.podcast
E.anycast
A.blocking
B.learning
C.disabled
D.forwarding
E.listening
A. Security increases because only the network administrator may change the routing tables.
B. Configuration complexity decreases as network size increases.
C. Routing updates are automatically sent to neighbors.
D. Route summarization iscompued automatically by the router.
E. Routing traffic load is reduced when used in stub network links
F. An efficient algorithm is used to build routing tables,using automatic updates.
G. Routing tables adapt automatically to topology changes.
A. to confine network instability to single areas of the network.
B. to reduce the complexity of router configuration
C. to speed up convergence
D. to lower costs by replacing routers with distribution layer switches
E. to decrease latency by increasing bandwidth
F. to reduce routing overhead
A.complicated header
B.plug-and-play
C.no broadcasts
D.checksums
E.optional IPsec
F.autoconfiguration
最新试题
When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?()
Which address is the IPV6 all-RIP-routers muticast group address that is used by RIPng as the destaion address?()
An administrator must assign static IP addresses to the servers in a network.For network 192.168.20.24/29, the router is assigned the first usable host address while the sales server is given the last usable host address. Which of the following should be entered into the IP propertied box for the sales server?()
After the show ip route command has been entered,the follwing routes are displayed.Which route will not be entered into the routing table of a neighboring router?()
Which device might be installed at a branch office to enable and manage an IPsec site-to-site VPN?()
The network administrator cannot to switch 1 over a telnet session,although the hosts attached to switch 1 can ping the interface Fa0/0 of the router.Given the information in the graphic and assuming that the router and switch2 are configured properly,which of the following commands should be issued on switch 1 to correct this problem?()
Which statement describes the rule of split horizon?()
Which Cisco IOS diagnostics command can disrupt the operation of a router under high-load conditions?()
Which IPsec security protocol should be used when confidentiality is required?()
While troubleshooting a network problem,a technician discovers that the current copy of the Cisco IOS is outdated and needs to be updated.Which of the following commands would the technician issue to replace the Cisco router IOS with the newer version?()