A. any-to-many communication model
B. delivery of packets to the group interface that is closest to the sending device
C. one-to-many communication model
D. the same address for multiple devices in the group
E. one-to-nearest communication model
F. a unique IPV6 address for each device in the group
您可能感兴趣的试卷
你可能感兴趣的试题
A.HMAC-MD5
B.RSA
C.HMAC-SHA-1
D.DH1
E.DH2
A.reduced cost
B.bette rthroughput
C.increased security
D.scalability
E.reduced latency
F.broadband incompatibility
A. EIGRP converges fast RIP because of DUAL and backup routes that are stored in the topology table.
B. EIGRP uses a hello protocol to establish neighbor relationships
C. EIGRP uses split horizon and reverse poisoning to avoid routing loops.
D. EIGRP uses periodic updates to exchange routing information
E. EIGRP allows routers of different manufacturers to interoperate
F. EIGRP supports VLSM and authentication for routing updates.
G. EIGRP use a broadcast address to send routing information.
A. CHAP uses a two-way handshake
B. CHAP authentication periodically occurs after link establishment
C. CHAP has no protection from playback attacks
D. CHAP authentication is performed only upon link establishment
E. CHAP uses a three-way handshake
F. CHAP authentication passwords are sent in plaintext
A. telnet access does not require a password
B. nat
C. no broadcast
D. chanage of destination address in the ipv6 header
E. chanage of source address in the ipv6 header
F. autoconfiguration
A. statically map IPV4 address to IPV6 addresses
B. configuration IPv4 tunnels between IPV6 islands
C. use DHCPv6 to map IPV4 addresses to IPV6 addresses
D. use proxying and translation to translate IPV6 packets into IPV4 packets
E. configure IPV6 directly
F. enable dual-stack routing
A.172.31.17.4/30
B.172.31.51.16/30
C.172.31.64.0/18
D.172.31.80.0/22
E.172.31.92.0/22
F.172.31.192.0/18
A. The number of FECN packets that are received by the router
B. The number of BECN packets that are received by the router
C. The ip address of the local router
D. The value of the local DLCI
E. The status of the PVC that is configured on the router
A. configure static frame relay map entries for each subinterface network.
B. remove the ip address from the physical interface
C. create the virtual interfaces with the interface command
D. configure each subinterface with its own IP address
E. disable split horizon to prevent routing loops between the subinterface networks
F. encapsulate the physical interface with multipoint PPP
A.show inventory
B.show flash:filesys
C.dirflash:include chassis
D.show diag
E.show controllers
最新试题
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?()Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
A network administrator needs to configure a serial link between the main office and a remote location.The router at the remote office is a non-cisco router. How should the network administrator configure the serial interface of the main office router to make the connection?()
You have been asked to come up with a subnet mask that will allow all three web servers to be on the same network while providing the max number of subnets.Which network address and subnet mask meet this requirement?()
On which options are standard access list based?()
An administrator must assign static IP addresses to the servers in a network.For network 192.168.20.24/29, the router is assigned the first usable host address while the sales server is given the last usable host address. Which of the following should be entered into the IP propertied box for the sales server?()
The network administrator cannot to switch 1 over a telnet session,although the hosts attached to switch 1 can ping the interface Fa0/0 of the router.Given the information in the graphic and assuming that the router and switch2 are configured properly,which of the following commands should be issued on switch 1 to correct this problem?()
Which encapsulation type is a Frame Relay encapsulation type that is supported by Cisco routers?()
Which Cisco IOS diagnostics command can disrupt the operation of a router under high-load conditions?()
Which command is used to display the collection of OSPF link states?()
Which command displays the CHAP authentication process as it occurs between two routers?()