A. Mismatched LMI types.
B. Incompatible encapsulation types.
C. Mismatching IP addresses.
D. Incorrect DLCI.
E. None of the above
您可能感兴趣的试卷
你可能感兴趣的试题
The Testking Central and Remote offices are configured as shown below:
The remote router can be successfully pinged from the central office but the remote users can't access the server at the central office.Based on the output above, what do you suspect is the cause of this problem?（）
A. The Frame Relay PVC is down.
B. The IP addressing on the Central/Remote serial link is incorrect.
C. RIP routing information is not being forwarded.
D. Frame Relay inverse-ARP is not properly configured.
While troubleshooting a serial line problem, you enable ppp authentication debugging as shown below:
Based on the command output above, what type of 'handshake' was used for PPP authentication?（）
A. one-way
B. two-way
C. three-way
D. four-way
E. no handshakes required during authentication
F. None of the above
A. 0.0.0.0
B. 0.0.0.255
C. 0.0.255.255
D. 0.0.7.255
E. 0.0.3.255
F. None of the above
A. show ppp authentication
B. debug PAP authentication
C. debug PPP authentication
D. show interface serial0
E. show CHAP authentication
A. show access-list
B. show ip access-list
C. show ip interface
D. show interface
E. show interface list
The relevant portion of the Barrymore router configuration is displayed below:
In your effort to conserve precious bandwidth, you set up some ACL's to deny internet access to the remote server located at 192.168.20.5. A few minutes after reconfiguring (as shown in the exhibit above) you notice that some web traffic is still going through.Based on the above output, what do you suspect as to why the traffic still traveling over the ISDN link?（）
A. Broadcasts are creating "interesting" traffic.
B. The access-list is not configured correctly.
C. The command ip access-group 129 out is missing from the bri0/0 interface.
D. The dialer-group has not been applied to outbound traffic.
A. show interface list
B. show ip route
C. show ip interface
D. show ip interface brief
E. show interface
On a newly installed router, the following access list is added to the HSSI interface for incoming traffic:Access-list 101 permit tcp any 10.18.10.0 0.0.0.255 eq tcp
What is the effect of the "any" keyword in the above access list?（）
A. check any of the bits in the source address
B. permit any wildcard mask for the address
C. accept any source address
D. check any bit in the destination address
E. permit 255.255.255.255 0.0.0.0
F. accept any destination
On your newly installed router, you apply the access list illustrated below to interface Ethernet 0 on a Cisco router. The interface is connected to the 192.168.1.8/29 LAN.
access-list 123 deny tcp 192.168.166.18 0.0.0.7 eq 20 any
access-list 123 deny tcp 192.168.166.18 0.0.0.7 eq 21 any
How will the above access lists affect traffic?（）
A. All traffic will be allowed to exit E0 except FTP traffic.
B. FTP traffic from 192.168.166.19 to any host will be denied.
C. FTP traffic from 192.168.166.22 to any host will be denied.
D. All traffic exiting E0 will be denied.
E. All FTP traffic to network 192.168.166.18/29 from any host will be denied.
最新试题
TestKing.com has allocated the IP add 199.144.27.0 is its network, to provide flexibility for the LAN design, a subnet mask of 255.255.255.240 has been chosen. Which of the following address can be assigned to LAN on the resulting subnets.（）
What is the subnetwork address for a host with IP address 201.100.5.68/28?（）
Which Frame Relay feature is responsible for transmitting keepalives to ensure that the PVC does not shut down because of inactivity?（）
What is the purpose of pressing the Ctrl+Break keys during the router password recover procedure?（）
Which of the following statements regarding routed and routing protocols are true?（）
What does a configuration Register Setting of 0x2105 indicate to the Router? （）
Which of the following if addresses can be assigned to host devices?（）
Which of the following contribute to congestion on an Ethernet network?（）
New switches have been purchased for a network upgrade. The objective for the network design emphasizes efficient, error-free transport instead of fast transport.Which switching mode should be configured on the new switches to provide error-free transport to the network? （）
What should the configuration register value be after successfully completing the password recover procedure and returning the router to normal operation? （）