Which command will need to be added to External_A to ensure that it will take over if serial 0/0 on External_B fails？ （）
A. standby 1 priority 130
B. standby 1 preempt
C. standby 1 track fastethernet 0/0
D. standby 1 track 10.10.10.1
您可能感兴趣的试卷
你可能感兴趣的试题
You want to allow Router R1 to immediately become the active router if its priority is highest than the active router fails.
What command would you use if you wanted to configure this？ （）
A. en standby preempt
B. standby preempt enable
C. standby preempt
D. hot standby preempt
A. Define the encapsulation type.
B. Define the standby router.
C. Define the standby IP address.
D. Enable the standby priority.
Refer to the exhibit. HSRP has been configured and Link A is the primary route to router R4. When Link A fails， router R2 （Link B） becomes the active router.
Which router will assume the active role when Link A becomes operational again？" （）
A. The primary router R1 will reassume the active role when it comes back online.
B. The standby router R2 will remain active and will forward the active role to router R1 only in the event of its own failure.
C. The standby router R2 will remain active and will forward the active role to router R1 only in the event of Link B failure.
D. The third member of the HSRP group， router R3， will take over the active role only in event of router R2 failure.
Refer to the exhibit. The Gateway Load Balancing Protocol has been configured on routers R1 and R2， and hosts A and B have been configured as shown.
Which statement can be derived from the exhibit？（）
A. The hostA default gateway has been configured as 10.88.1.10/24.
B. The GLBP weighted load balancing mode has been configured.
C. The GLBP round-robin， load-balancing mode has been configured.
D. The GLBP host-dependent， load-balancing mode has been configured.
E. The hostA default gateway has been configured as 10.88.1.1/24.
F. The hostA default gateway has been configured as 10.88.1.4/24.
Which command will need to be added to External_A to ensure that it will take over if serial 0/0 on External_B fails？（）
A. standby 1 priority 130
B. standby 1 preempt
C. standby 1 track fastethernet 0/0
D. standby 1 track 10.10.10.1
Routers can send hello messages in three HSRP states.
Which ones are they？（）
A. Standby
B. Learn
C. Listen
D. Speak
E. Active
Router R1 is configured for HSRP.
Which of the following are valid HSRP states on R1？ （）
A. Init
B. Idle
C. Active
D. Standby
E. Established
F. Backup
You have configured router R1 with HSRP， using the standard defaults.
Which three statements are true of a default HSRP configuration？（）
A. The Standby hello time is 2 seconds.
B. Two HSRP groups are configured.
C. The Standby track interface priority is 10.
D. The Standby hold time is 10 seconds
E. The Standby priority is 100.
F. The Standby delay is 3 seconds.
You need to design router redundancy on the Company network.
Which three protocols could be chosen for IP routing redundancy to protect against first-hop router failure？（）
A. GLBP
B. ICMP
C. MSTP
D. HSRP
E. VRRP
F. NHRP
Router R1 and R2 are both configured for HSRP.
Which two statements about the HSRP priorities of these two routers are true？（）
A. To assign the HSRP router priority in a standby group， the standby group-number priority priority-value global configuration command must be used.
B. The default priority of a router is zero （0）.
C. The no standby priority command assigns a priority of 100 to the router.
D. Assuming that preempting has also been configured， the router with the lowest priority in an HSRP group would become the active router.
E. When two routers in an HSRP standby group are configured with identical priorities， the router with the highest configured IP address will become the active router.
最新试题
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command， which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true？（）