A. PIN photodiodes
B. zero-chirped lasers
C. Erbium-doped fiber amplifiers
D. dispersion compensating fiber
E. dispersion compensating Bragg grating
您可能感兴趣的试卷
你可能感兴趣的试题
A. They are both regions of lowest loss.
B. They are both regions of low reflections.
C. They are both regions of low index of refraction.
D. They are both regions of low chromatic dispersion.
E. They are both regions of low Polarization Mode Dispersion (PMD).
A. low optical powe
B. high optical power
C. few optical channels
D. many optical channels
E. low chromatic dispersion
F. high chromatic dispersion
G. too much power differential in the optical channels
Given the formula: (Fiber Attenuation * Km) + (Splice Attenuation * # of Splices) + (Connector Attenuation * # of Connectors) + (Optical Fiber or OADM) + Buffer(Fiber aging)) With regard to SONET/SDH optical calculations,
what will the given formula provide?()
A. fiber loss
B. OSNR level
C. post amplification
D. index of reflection
E. index of refraction
F. power post amplification budget
Click the Exhibit button.
Which type of multiplexer is shown in the exhibit?()
A. Thin Film filter
B. Fiber Bragg Grating
C. Arrayed Wave Guide
D. Erbium fiber amplifier
A. fiber dispersion
B. signal attenuation
C. transmitter power
D. amplifier bandwidth
E. receiver dispersion tolerance
A. 0 ps/nm
B. 340 ps/nm
C. 200 ps/nm
D. 3400 ps/nm
E. More information is needed.
A. The glass core is doped with an Erbium in periodic segments of the fiber.
B. Layers of high index ?and low index ?material are deposited on a glass substrate.
C. Thin layers of silica glass are placed onto wafers to produce a prism-like effect.
D. Fiber is etched with an ultraviolet laser that is precisely spaced for specific wavelength filtering.
Click the Exhibit button. When designing a DWDM system with multiple amplified spans, a pre-amp is needed at Site B to ().
A. offset the OADM loss at site B
B. overcome the high multiplexer loss at site A
C. amplify signal levels after the high loss through Fiber Span 1
D. adjust add channels at site B to be at the same level as the passthrough channels
E. ensure that the per channel power is higher than the minimum needed for the post-amp at Site B
In the OSNR model for EDFA amplifiers, SNR OUT = 1/(1/SNR IN + FhvB/P IN ),
what does SNR IN represent?()
A. the signal to noise of the current optical amplifier
B. the signal to noise of the previous amplifier or source
C. the signal to noise introduced by the optical multiplexer
D. the accumulated noise to signal ratio of the optical channel
The dispersion of a non-zero dispersion shifted fiber is 6 ps/nm*km at 1550 nm and 10 ps/nm*km at 1610 nm.
What is the minimum dispersion compensation required if an L-Band DWDM signal travels through 200 km of fiber and has a dispersion tolerance of 1800 ps/nm?()
A. none
B. -600 ps/nm
C. -200 ps/nm
D. +200 ps/nm
E. +600 ps/nm
最新试题
How is SNCP and MS-SPRing traffic rerouted during a protection switch when a complete fiber cable cut occurs?()
A VC-4-4c consists of ().
What is an advantage of an externally modulated laser over a directly modulated laser? ()
The dispersion of a non-zero dispersion shifted fiber is 6 ps/nm*km at 1550 nm and 10 ps/nm*km at 1610 nm. What is the minimum dispersion compensation required if an L-Band DWDM signal travels through 200 km of fiber and has a dispersion tolerance of 1800 ps/nm?()
What are three relevant design considerations when using the 15216 EDFA?()
A 2.5 Gb/s (OC-48 or STM-16) optical signal with a dispersion tolerance of 1200 ps/nm goes through fiber with 18ps/nm*km of dispersion. How many 15216-DCU-350 equivalents are needed for enough compensation after traveling 100 km?()
Which two can be transported in one AU-4? ()
What protection method is used in 4F MS-SPRing networks?()
What is the difference between the transmitted power and the sensitivity of the receiver? ()
What is the phenomenon called where different wavelengths of light travel at different speeds?()