A. amplifier
B. attenuator
C. regenerator
D. light emitter
E. optical switch
F. optical receiver
G. fiber-optic cable
您可能感兴趣的试卷
你可能感兴趣的试题
A. OSNR
B. dispersion
C. attenuation
D. power budget
E. amplifier spacing
F. four wave mixing
A. PIN photodiodes
B. zero-chirped lasers
C. Erbium-doped fiber amplifiers
D. dispersion compensating fiber
E. dispersion compensating Bragg grating
A. They are both regions of lowest loss.
B. They are both regions of low reflections.
C. They are both regions of low index of refraction.
D. They are both regions of low chromatic dispersion.
E. They are both regions of low Polarization Mode Dispersion （PMD）.
A. low optical powe
B. high optical power
C. few optical channels
D. many optical channels
E. low chromatic dispersion
F. high chromatic dispersion
G. too much power differential in the optical channels
Given the formula： （Fiber Attenuation * Km） + （Splice Attenuation * # of Splices） + （Connector Attenuation * # of Connectors） + （Optical Fiber or OADM） + Buffer（Fiber aging）） With regard to SONET/SDH optical calculations，
what will the given formula provide？（）
A. fiber loss
B. OSNR level
C. post amplification
D. index of reflection
E. index of refraction
F. power post amplification budget
Click the Exhibit button.
Which type of multiplexer is shown in the exhibit？（）
A. Thin Film filter
B. Fiber Bragg Grating
C. Arrayed Wave Guide
D. Erbium fiber amplifier
A. fiber dispersion
B. signal attenuation
C. transmitter power
D. amplifier bandwidth
E. receiver dispersion tolerance
A. 0 ps/nm
B. 340 ps/nm
C. 200 ps/nm
D. 3400 ps/nm
E. More information is needed.
A. The glass core is doped with an Erbium in periodic segments of the fiber.
B. Layers of high index ？and low index ？material are deposited on a glass substrate.
C. Thin layers of silica glass are placed onto wafers to produce a prism-like effect.
D. Fiber is etched with an ultraviolet laser that is precisely spaced for specific wavelength filtering.
Click the Exhibit button. When designing a DWDM system with multiple amplified spans， a pre-amp is needed at Site B to （）.
A. offset the OADM loss at site B
B. overcome the high multiplexer loss at site A
C. amplify signal levels after the high loss through Fiber Span 1
D. adjust add channels at site B to be at the same level as the passthrough channels
E. ensure that the per channel power is higher than the minimum needed for the post-amp at Site B
最新试题
Click the Exhibit button. Within an ONS 15454， you are provisioning a circuit on an unprotected SNCP ring. In the exhibit， which two must you configure？（）
Which is a legitimate bandwidth matched pair？（）
In order to avoid misconnections due to a failed node in an MS-SPRing， Alarm Indication Signals （AISs） are sent on every channel normally terminating in that node. What is the name of this process？（）
Which two can be transported in one AU-4？ （）
In the OSNR model for EDFA amplifiers， SNR OUT = 1/（1/SNR IN + FhvB/P IN ）， what does SNR IN represent？（）
How is SNCP and MS-SPRing traffic rerouted during a protection switch when a complete fiber cable cut occurs？（）
Which device creates an OEO conversion？ （）
A VC-4-4c consists of （）.
What are three factors that limit the maximum distance of an amplified optical signal without regeneration？ （）
For lasers with tightly controlled wavelengths， approximately how far apart are the centers of adjacent wavelengths when 100 GHz spacing is used in a DWDM system？ （）