Click the Exhibit button. What is the maximum allowable loss budget between the ONS 15216 Mux （left side） composite output and the ONS 15216 Demux （right side） composite input，
with the optical values given in the exhibit？ （Assume the worst case loss of 4.5 dB for 15216 200 GHz Mux/Demux and ignore power penalties or extra margin.） （）
A. 15 dB
B. 17 dB
C. 21 dB
D. 26 dB
E. 27 dB
您可能感兴趣的试卷
你可能感兴趣的试题
A 2.5 Gb/s （OC-48 or STM-16） optical signal with a dispersion tolerance of 1200 ps/nm goes through fiber with 18ps/nm*km of dispersion.
How many 15216-DCU-350 equivalents are needed for enough compensation after traveling 100 km？（）
A. none
B. one
C. two
D. three
E. four
The ONS 15216 is a 32-channel system. The ONS 15216 OADMs are capable of adding and dropping one， two， or four channels.
How are the OADMs provisioned to add and drop specific channels？（）
A. The ONS 15216 OADM can be provisioned to add/drop one， two， or four channels via Cisco Transport Manager （CTM）.
B. The ONS 15216 OADM consists only of a four-channel module， and the number of ports utilized determines whether it is a one， two， or four channel OADM.
C. Three separate OADM modules are available for one， two， and four channels. The wavelengths to be dropped and added are programmable via Cisco Transport Manager （CTM）.
D. The ONS 15216 OADM consists only of a single-channel module. Two-channel and four-channel support is available by stacking the single-channel module.
E. The ONS 15216 OADM is available in one， two， four channels. There are 32 single-channel OADM modules， 16 two-channel OADM modules， and 8 four-channel OADM modules.
A. dispersion
B. Optical SNR
C. span attenuation
D. four wave mixing
E. receiver sensitivity
A. 0 mW
B. 1 mW
C. 10 mW
D. 1.5 mW
A. lower cost
B. higher chirp
C. easier to manufacture
D. higher dispersion tolerance
E. higher optical signal-to-noise ratio
A. OSNR
B. dispersion
C. light skew
D. attenuation
A. amplifier
B. attenuator
C. regenerator
D. light emitter
E. optical switch
F. optical receiver
G. fiber-optic cable
A. OSNR
B. dispersion
C. attenuation
D. power budget
E. amplifier spacing
F. four wave mixing
A. PIN photodiodes
B. zero-chirped lasers
C. Erbium-doped fiber amplifiers
D. dispersion compensating fiber
E. dispersion compensating Bragg grating
A. They are both regions of lowest loss.
B. They are both regions of low reflections.
C. They are both regions of low index of refraction.
D. They are both regions of low chromatic dispersion.
E. They are both regions of low Polarization Mode Dispersion （PMD）.
最新试题
Click the Exhibit button. The exhibit shows a 15454/15216 DWDM system and alarm indications. What are two possible sources of trouble shown in the system？（）
Which device creates an OEO conversion？ （）
How is SNCP and MS-SPRing traffic rerouted during a protection switch when a complete fiber cable cut occurs？（）
In the OSNR model for EDFA amplifiers， SNR OUT = 1/（1/SNR IN + FhvB/P IN ）， what does SNR IN represent？（）
Which timing mode is appropriate for an SDH NE that is adjacent to an SDH NE Bits-1 timing？ （）
What three in combination are factors that can cause four-wave mixing in fiber-optic cables？（）
Click the Exhibit button. Which type of multiplexer is shown in the exhibit？（）
What protection method is used in 4F MS-SPRing networks？（）
What is the phenomenon called where different wavelengths of light travel at different speeds？（）
Which two can be transported in one AU-4？ （）