A.2031：0：130F：0：0：09C0：876A：130B
B.2031：：130F：：9C0：876A：130B
C.2031：0：130F：：9C0：876A：130B
D.2031：0：130F：0：0：9C0：876A：130B
您可能感兴趣的试卷
你可能感兴趣的试题
A.Traffic forwarded from R2 to or through R1 will continue to be forwarded based on the forwarding table state at the time of the reload.
B.R2 will continue to forward traffic to R1， but R1 will drop the traffic because its neighbor adjacency with R2 has failed.
C.R2 will continue forwarding traffic to and through R1， but R1 will drop this traffic because it is not capable of maintaining its forwarding state.
D.All the traffic R2 is forwarding to or through R1 will be dropped while OSPF rebuilds its neighbor adjacency and forwarding tables.
A.It ensures that BPDUs sent by the root bridge are forwarded in a timely manner
B.It enforces the root bridge placement in the network
C.It ensures that all ports receiving BPDUs from the root bridge are in the forwarding state.
D.It ensures that the bridge is elected as root bridge in the network.
A.IPv6 multicast uses Multicast Listener Discovery.
B.The first 8 bits of an IPv6 multicast address are always FF （1111 1111）.
C.IPv6 multicast requires MSDP.
D.PIM dense mode is not part of IPv6 multicast.
A.Sent by the destination
B.Received by the sender
C.Received by the destination
D.Sent by the sender
A.Only UplinkFast and BackboneFast are specified in 802.1w； PortFast must be manually configured.
B.Only PortFast is specified in 802.1w； UplinkFast and BackboneFast must be manually configured.
C.None of the proprietary Cisco enhancements are specified in 802.1w.
D.PortFast， UplinkFast， and BackboneFast are specified in 802.1w.
A.Speed mismatch
B.Incorrect encapsulation
C.MTU set too low
D.Duplex mismatch
A.EBGP multihop will need to be configured for this to work.
B.This should work with normal BGP peering， with no additional configuration on the BGP speakers or the firewall.
C.The BGP protocol port must be opened on the firewall
D.There is no way to make BGP work across a firewall.
A.The stack bit will only be used when LDP is the label distribution protocol
B.The label is the last entry in the label stack.
C.The stack bit is for Cisco implementations exclusively and will only be used when TDP is the label distribution protocol.
D.The stack bit is reserved for future use.
A.Reverse Path Forwarding
B.Hardware-based forwarding
C.UDP forwarding
D.Layer 2 Forwarding
A.The firewall does not support Cisco Discovery Protocol. You should set the switchport trunk mode ON
B.The firewall does not support Cisco Discovery Protocol. You should set the switchport trunk mode to OFF
C.The firewall does not support Cisco Discovery Protocol. You should set the switchport trunk mode asauto.
D.The firewall does not support DTP. You should set the switchport trunk mode to ON
最新试题
For the following items，what is the mathematical relationship between the committed information rate （CIR）， committed burst （Bc）， and committed rate measurement interval （Tc）？（）
What does the OSPF command capability vrf-lite achieve？（）
Which statement best describes OSPF external LSAs （type 5）？（）
What is the STP root guard feature designed to prevent？（）
Multicast is being deployed in the network， and only ip pim sparse-dense mode has been configured on all interfaces in the network to support a new video streaming application. No other multicast configuration was applied anywhere in the network. Since enabling multicast， the network monitoring tools show periodic spikes in link utilization throughout the network， even in areas where the video application is not being used. What could be a possible cause？（）
For the following protocols， which one provides a mechanism to transparently intercept and redirect CIFS traffic from a client to a local Cisco Wida Area Application engine？（）
What is the command to configure RSVP to reserve up to one-tenth of a Gigabit link， but only allow each individual flow to use 1 MB/s？（）
In GLBP， which router will answer on client ARP requests？（）
You are the network administrator of an enterprise company that just deployed a global IP telephony environment. In order to guarantee good voice quality， you asked your provider to implement QoS on the CE routers of your MPLS network. On your LAN， you have also deployed QoS. Users， however， keep complaining about bad voice quality， and the provider does not see matches on the DSCP values that you have asked him to match upon. What is most likely the problem？（）
Which QoS mechanism can help classify different kinds of Citrix traffic （print job versus real-time terminal control）？（）